ISSUE: ENGINE STALLS AFTER WARM UP WHEN COMING TO A STOP @ THAT POINT MORE DIFFICULT THAN THE NORM TO START NEED'S THROTTLE INPUT TO KEEP IDLING
Still having this dang issue, after its warmed...
Type: Posts; User: 14HemiRam
ISSUE: ENGINE STALLS AFTER WARM UP WHEN COMING TO A STOP @ THAT POINT MORE DIFFICULT THAN THE NORM TO START NEED'S THROTTLE INPUT TO KEEP IDLING
Still having this dang issue, after its warmed...
Just change the rpm issues and my buddy is driving right now and it seems to have a slight surge and almost died from a stop. Does my friction torque setup look correct I had made changes to that...
Ok so Im running the stock 5.7 ECU and have swapped in a 6.4 with MMX Max Effort Cam 3200 stall & 8 speed.
ISSUE: Start truck and after it warms up when I come to a stop it will die 3x's out of 10...
Question on the displacement setting. Does the displacement not need to be set according to the engine displacement? I replaced my 5.7 with a 6.4 engine and I changed my displacement according to...
Im guessing you dialed in your injectors by now, I have a question I have swapped a 6.4 into my Ram from a 5.7 Im using the 6.4 truck intake along with the 6.4 injectors that came with it. Ive...
shak3r Ok thanks for the response. Would you happen to still have one of your tunes for that cam that I could do some comparisons with? Thanks
Older thread I know but I?m curious as to how it turned out for you using ANN? I just installed a 6.4 with 12.1 CR and I?m needing to get it dialed in was curious as to how well it worked?
I have the same cam hpt+ and I have it set at
112* max phase
120* exhaust lock-pin
133* exhaust max
112* exhaust min
I'm using the 7* comp limiter as well. I think it's set correct my original...
Have you come across any? Anyway you could share you stock file my son has a 96 Ram 360 and was wanting to check out what all can be tuned. Thanks
First of all thanks for all the help greatly appreciate the help! My cats are deleted, I'm building off the original tune I had got from hemifever which is where some of the knock sensors...
Ok I added a log in with them. Thanks for the help!
BTW which tune would you like the one before the Neural Network tune, basically the one I used to upload, or the tune after the neural network touched it?
That would be great I'll send it over. Appreciate it.
Curious Ive been trying out the Neural Network Trainer and I am having a hard time with it. Is there somewhere I can get some good info on how to use the trainer? I haven't found much on this...
OK I'm looking into it right now I'll update if it worked or not! Thanks for responding!
* to verify under the "torque converter" tab I disable "tcc enable" 1st gear to "disable" to see if it's...
I've been wanting to mess with it but not sure if anyone has figured out the best place to run that runner.
New to this so may chance I'm getting this wrong... But could that have anything to do with as you slow down and it downshifts into First gear only it has an uncomfortable jerking downshift by...
I'm and pretty new as well. Thanks for taking the time to put those up.
I actually just installed:
HEMI VVT cam grind
.591Int - .581Exh lift w/1.65rr
@50 214 - 224
MDS Delete Kit
If you'd like to look up my cam it's the MMP-214-224HPT+ from MMX
And I ended up...
I'm new to tuning and installed a new mmx 214 224 cam in my 14 Ram 5.7 it's run ING rich on LTFT its adjusting - 30% STFT is about - 1.8%
I would assume the reason you lost boost was due to your ability to flow more are through the motor boost measures pressure therefore the more air flowing easily through motor with same pulley on...