Search:

Type: Posts; User: nicul15

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    47
    Views
    2,580

    what are you doing to the table? maxing it out?

    what are you doing to the table? maxing it out?
  2. Bringing this thread back. Hoping you can help. I...

    Bringing this thread back. Hoping you can help. I have a 2014 Silverado 4.3l gen5 v6 and have a gen5 6.2 laying around. Physically this would not be difficult compared to past gens, as it?s a gen5...
  3. Replies
    3
    Views
    193

    can you post your tune file?

    can you post your tune file?
  4. Replies
    47
    Views
    2,580

    So it could be a hysteresis on the throttle?...

    So it could be a hysteresis on the throttle? Sounds like thats what this table controls.
  5. once it asks to do a regen you're screwed. you...

    once it asks to do a regen you're screwed. you need to put all the equipment back in to clear the condition.
  6. Replies
    47
    Views
    2,580

    request sent to support for the 16 6thgen ss

    request sent to support for the 16 6thgen ss
  7. Replies
    47
    Views
    2,580

    How do you request them? I don?t see them on a 16...

    How do you request them? I don?t see them on a 16 ss
  8. Replies
    2
    Views
    301

    You can select what gears you want it enabled in...

    You can select what gears you want it enabled in too
  9. How rich we talking here?

    How rich we talking here?
  10. What converter and was it locked?

    What converter and was it locked?
  11. That works but one thing i might add is most do...

    That works but one thing i might add is most do the vve and run through all the load cells in one gear. Otherwise the map wont represent the engine if the different loads from the different gears...
  12. Replies
    6
    Views
    272

    is that PE realistic?

    is that PE realistic?
  13. Replies
    24
    Views
    1,834

    Does running vve scoop up tuning for a bigger...

    Does running vve scoop up tuning for a bigger ported tb?
  14. Replies
    24
    Views
    1,834

    Is your tb ported?

    Is your tb ported?
  15. Replies
    33
    Views
    2,377

    Also peak torque gets within 45-50 of max torque....

    Also peak torque gets within 45-50 of max torque. Is that too close? Should it be 100 above?
  16. Replies
    33
    Views
    2,377

    Thanks, I dont fully trust the tps and timing...

    Thanks, I dont fully trust the tps and timing pids(I do log all of them). I usually look at g/cyl and map to make sure its all wide open. By working with this one car a lot I have a sense of where it...
  17. Replies
    33
    Views
    2,377

    Slight high Jack. Running Bolt ons. Car is...

    Slight high Jack. Running Bolt ons. Car is running great mpg is up and gained 1.5 mph over my old tune since I did the vve.

    The only thing I see is the demanded torque percentage falls under 100%...
  18. Replies
    14
    Views
    889

    I think theres an editable field that says what...

    I think theres an editable field that says what temp it was calibrated in. It says 68* stock and I zeroed mine in when it was that temp outside to be sure. I?m pretty sure that?s what the description...
  19. Replies
    9
    Views
    535

    If they are more than 5,000 miles use new ones. ...

    If they are more than 5,000 miles use new ones. Gm service manual says new EVERY time.

    I can?t say how many ppl chase their tail because of this
  20. Replies
    9
    Views
    535

    So it uses stock gaskets? Were they new or did...

    So it uses stock gaskets? Were they new or did you reuse them?
  21. Replies
    9
    Views
    535

    I?d fog it. What about the port seals by the...

    I?d fog it. What about the port seals by the heads. Don?t they use spacers there?
  22. Replies
    9
    Views
    535

    Sounds mechanical like a vacuum leak. Sorry don?t...

    Sounds mechanical like a vacuum leak. Sorry don?t think it?s the tune
  23. Replies
    2
    Views
    191

    The lockup for shifts are in the trans settings....

    The lockup for shifts are in the trans settings. You can set it for each gear
  24. Replies
    56
    Views
    5,710

    Thank you!

    Thank you!
  25. Replies
    56
    Views
    5,710

    Guys this one piece of info would help me. Do I...

    Guys this one piece of info would help me. Do I let it idle when doing maf only in idle Hz? I know if I do this it would idle better but I want to do this the right way not the easy way.

    Looking...
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4