Search:

Type: Posts; User: fastslvblkcar

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    1,017

    The reason I have so many pids is that I use...

    The reason I have so many pids is that I use standalone logging and I use this on multiple vehicles. I also log a lot of information because I race this truck and am a data whore. Here is a log from...
  2. Replies
    16
    Views
    1,017

    Is it not lean compared to the desired? Wouldn't...

    Is it not lean compared to the desired? Wouldn't this cause an idle surge? Especially in cooler temps?
  3. Replies
    16
    Views
    1,017

    It never goes into closed loop as it is not...

    It never goes into closed loop as it is not enabled. Compare the desired to the actual Lambda and you can see the lean condition.
  4. Replies
    16
    Views
    1,017

    Blindsquirrel responded to a post of mine about...

    Blindsquirrel responded to a post of mine about this earlier this year and I couldn't find the thread. I just found it. The lean condition isn't just over 1.0 lambda, it is higher than commanded...
  5. Replies
    16
    Views
    1,017

    I was just asking of this lean condition from the...

    I was just asking of this lean condition from the rear oxygen sensors can be tuned by using the initial adders and decay delay. I wasn't asking for you to inspect my tune file and see what I need to...
  6. Replies
    16
    Views
    1,017

    Lean for ~60 seconds after start up

    So, I have been told this is due to not having rear O2 sensors. Can this be tuned out (ish) by using Cold Warmup After Start initial adder and decay delays? I have been fighting this lean condition...
  7. Replies
    28
    Views
    2,295

    I have an update. I rebuilt the transmission and...

    I have an update. I rebuilt the transmission and got it back in. I went to drive it and didn't make it out of the driveway before the grinding noise returned. I was datalogging at the time which...
  8. Replies
    28
    Views
    2,295

    Well this is where it is at now. I would like to...

    Well this is where it is at now. I would like to fix the hesitation but it is kinda hard to tune VE when I can't even move the car.
  9. Replies
    28
    Views
    2,295

    It is not the brake switch from the escalade but...

    It is not the brake switch from the escalade but it does work the same way. I am planning on working on the VE however when I got the engine running and was able to move the car in the driveway I...
  10. Replies
    28
    Views
    2,295

    I replaced the gaskets and retested the intake...

    I replaced the gaskets and retested the intake and now have a good seal. I did get it running after this and am getting a pretty bad hesitation when hitting the throttle.
  11. Replies
    28
    Views
    2,295

    So I was worried about a vacuum leak while I was...

    So I was worried about a vacuum leak while I was cranking it over and it starting as lean as it was. I also noticed the it was idling at 65kPa on the MAP sensor. I brought the smoke machine home with...
  12. Replies
    28
    Views
    2,295

    The only code set is a self induced P0103. You...

    The only code set is a self induced P0103. You can see in the data log that the TPS moves with the APP.
  13. Replies
    28
    Views
    2,295

    Well, I inputted the injector data and put the...

    Well, I inputted the injector data and put the tune in and now it is so lean cranking that I could only get it to start and stay running 1 time. This time again I could not get the engine to rev with...
  14. Replies
    28
    Views
    2,295

    Yeah, I was thinking that but I mostly have just...

    Yeah, I was thinking that but I mostly have just made changes to base air flow, based off of other people that have the 408 setup and had been running it. That stuff helped me get it running and stay...
  15. Replies
    28
    Views
    2,295

    I understand completely. I am constantly arguing...

    I understand completely. I am constantly arguing with our service writers because they get suck poor information from customers. I will get this data put in and programmed tonight and run a log and...
  16. Replies
    28
    Views
    2,295

    yes, it is running at 58psi. That is why I added...

    yes, it is running at 58psi. That is why I added the inline was to verify that it was otherwise why add a gauge? This isn't a civic where you add gauges because it is "cool". I am at work for another...
  17. Replies
    28
    Views
    2,295

    I added an inline gauge.

    I added an inline gauge.
  18. Replies
    28
    Views
    2,295

    If this is correct for my fuel system, I will...

    If this is correct for my fuel system, I will program it tonight and see what happens. Thanks for the help.
  19. Replies
    28
    Views
    2,295

    Fuel pump - Walbro 450lph fuel filter - 58psi...

    Fuel pump - Walbro 450lph
    fuel filter - 58psi corvette style internal regulator
  20. Replies
    28
    Views
    2,295

    It has been a year since I added the data that I...

    It has been a year since I added the data that I found. I was just looking back through it and I couldn't have gotten the data from a stock vehicle file. I don't know where I got that data. What do I...
  21. Replies
    28
    Views
    2,295

    I used GM PN 12609749. I looked up what vehicle...

    I used GM PN 12609749. I looked up what vehicle they would have came on and copied the injector data from a stock file I got from the repository.
  22. Replies
    28
    Views
    2,295

    Won't come off idle

    I will give you the build first. This is a new built 408ci stroker. It has a BTR stage 4 400ci+ camshaft in it with some LS3 heads. I am running a drive by wire setup with the adapter for 8 to 6 pin...
  23. Replies
    3
    Views
    533

    Is there a way to add fuel at that point to...

    Is there a way to add fuel at that point to reduce it? I removed the rear sensor wiring 2 years ago when I installed this setup and no longer have the old stuff. and it is too much of a pain int the...
  24. Replies
    3
    Views
    533

    Lean for ~30 seconds after start up

    I am running a 6.0L with the Honey Badger cam. I have upgraded the springs, push rods and lifters. I have 34lbs injectors, a TBSS intake and shorty headers. When I start the engine, It runs great...
  25. Replies
    17
    Views
    3,007

    Here is another one that went way lean after...

    Here is another one that went way lean after startup.
Results 1 to 25 of 65
Page 1 of 3 1 2 3