I was able to install both versions of VCM suite and FYI for anyone that stumbles across this thread, version 4.9.264.0 (Beta) did allow access to re-enable the O2 sensors.
Thanks again JohnnyFW!!
Type: Posts; User: 1SLwLS1
I was able to install both versions of VCM suite and FYI for anyone that stumbles across this thread, version 4.9.264.0 (Beta) did allow access to re-enable the O2 sensors.
Thanks again JohnnyFW!!
You are the man! I owe you a million. Within the next few weeks, I was going to start the process of ordering a PCM, getting a dealer to flash the latest update, backdoor the transmission settings,...
Wait, so something was off in the tune file and you fixed/uploaded it? If so, thank you so much!
I can't upload the tune to test it out until I get home as I drove the mustang to work today, but I...
To the best of my knowledge, I have all of the stock diagnostics enabled. I have only been able to compare to a couple of repository tunes though as the original tuner did not save my stock file. Are...
TLDR
Missing STFTs on B2, always 0%
Looking back, its been that way for a while
B2 has weird voltages and no O2 heaters
Testing sensors, wiring, etc, all diagnostics tests lead to replace...
Instead of disconnecting the battery to reset fuel trims, I will use AlfaOBD unless anyone can confirm the fuel composition reset in VCM scanner.
This past weekend I performed several oxygen sensor and heater circuit diagnostic tests from codes likes P0032, P113E, P0133, P2271, etc. The diagnostics performed via AllDataDIY had me checking...
Alright so I turned on the PID for O2 heater duty cycle and can see for sure that the ECM is not commanding B2 to turn on. Now it is a case of the chicken and the egg, is the heater circuit not...
Alright so after I got home from dance last night, everything was warm and hot and had been running for over 30 minutes on back country highways. I swapped back B1S1 and B2S1 so they're in their...
So tonight I was able to disconnect the upstream sensors on both banks and measure the voltage. I started the truck and waited for CL and then disconnected the terminal on B1S1 (sensor that was...
Vehicle: 2013 Ram 1500 4x2 CC (GPEC2)
Engine: SRT 6.4 with MMX NSR Cam (220/232 @ 0.050 & 0.597/0.553 LSA 112.5), ported 6.4 truck intake, 1 3/4" ARH LTs, Off-Road Y
Transmission: 3600 Street Edge...
You need a yoke from a 66RFE. I hope you get it working, 8 speed swap still in progress.
So I tried but the truck didn't recognize it; I was told that the solenoid pack is a likely culprit but didn't want to dump more money into that experiment. Oddly enough, when I ended up rebuilding...
105909
Thank you for the stock tune! I have attached here since I cannot upload to the stock tune repository (after a quick search, it seems this isn't an available feature yet).
Hopefully it...
Does anyone have the stock tables from a 66RFE transmission? I am attempting to replace my 65RFE with a 66RFE and it would be good to compare with my 65RFE tables to see what (if anything) else needs...
I think I?m going to give it a try and see what happens
But is it as easy as adjusting some tuning parameters for the 2WD crowd or will it not work? When I see posts in the past about adjusting the PCM for various transmissions, they always say it can?t...
I have a 2013 Ram 1500 2WD Sport that I bought new in 2013 and has around 166K mi on the transmission now. I wish I would've waited 6 months for an 8-speed but I needed a new vehicle and no dealers...