Search:

Type: Posts; User: GrannySShifting

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. I want a log from a stock tune stock car WOT pull...

    I want a log from a stock tune stock car WOT pull just like i said Haha
  2. I don't see any throttle closure, timing pulled...

    I don't see any throttle closure, timing pulled or anything as a result of that? I'll try and see
  3. Tune file doesnt have anything to do with it, its...

    Tune file doesnt have anything to do with it, its a manual boost controller
  4. 2.4 L, oem 2.0 turbo/manifold on it, boost spikes then falls off hard

    What boost should these be able to make? With a manual controller on it spikes to 8.7 falls to 3 psi. Turn controller up a bit it makes 15 psi and falls wayyy back to 6 psi
  5. I think i didnt realize I had undid me earlier PE...

    I think i didnt realize I had undid me earlier PE settings in a flash revision. Seems to be a little bit better
  6. So the lower end of the casting is different on...

    So the lower end of the casting is different on the 2.4 its not just a bigger bore?

    I meant stock pistons/rods etc really what could they take
  7. Power enrich delay even though there shoudlnt be?

    Can see if doesnt go into power enrich until 4100 rpm/68% pedal/148 kPa even though it should above 25% pedal?
  8. Anyone have logs from stock NA and turbo Ecotec?

    Full gear pull on dyno or highway?
  9. Ecotec/Solstice engine /fuel system limits

    How far have people pushed the NA 2.4 boosted?

    How about the turbo 2.0?

    The GXP solstice is all direct injected right, how far can those injectors go if you have enough low side fuel system?
  10. Threw odd codes, nuetraled out in 4-5-6 think, drove fine after restart?

    After clearing codes everything turned back to normal, trans was just put in, he pulled the TCM out of his original trans and put it in this one. Codes were P0700 and P2724 which is one of the...
  11. Replies
    9
    Views
    935

    Most E38 have this setting

    Most E38 have this setting
  12. Replies
    9
    Views
    935

    Anyone?

    Anyone?
  13. Replies
    79
    Views
    32,683

    Sticky: They call it vaporware I think? :banghead:

    They call it vaporware I think? :banghead:
  14. Replies
    15
    Views
    1,310

    Change the Delay Volume and Transition Volume to...

    Change the Delay Volume and Transition Volume to 0 - sometimes takes long time for it to realize change in content with stock settings
  15. Replies
    18
    Views
    4,401

    Can you post up what you ended up with?

    Can you post up what you ended up with?
  16. 2012 CTSV, cant even log MAP raw voltage?

    Scanner maxes at 255 kPa reported, on others I just log MAP raw voltage and you can figure out from there depending on what MAP your using, but scanner doesnt even show that as an option?:banghead:
  17. After digging around it that's what I was...

    After digging around it that's what I was assuming. I can physically scale three axis so it can read a LS9 map, but does that work as it should?

    This must have been done with an OLD version of...
  18. I had to refresh the page, guess it kept the post...

    I had to refresh the page, guess it kept the post and I didnt notice it didnt keep the attachments??
  19. 2015 SS but virtual VE isnt in edit menu like normal, in reg tables?

    Whats deal with this
  20. Replies
    2
    Views
    252

    Factory line lock

    Can this be enabled with HPTuners, supposedly somethign called Tazer can add the function plugged into OBDII port
  21. I was never able to figure this one out

    I was never able to figure this one out
  22. Replies
    0
    Views
    387

    0-5v sensor noise

    Logging on OEM pcm some of the pressure sensors dont have clean readings. Is there some way to clean these up so they log a little more stably? The factory pressure sensors on these inputs (fuel tank...
  23. Think he jumped off nearest cliff. in car.

    Think he jumped off nearest cliff. in car.
  24. Worried about the Hemi powered stuff mainly

    Worried about the Hemi powered stuff mainly
  25. The earlier versions of these have no flex sensor support correct?

    Are there any 0-5v inputs that can be used to influence fueling etc? I think Ive seen some work arounds people are trying?

    When and what ECUs started getting flex capable support?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4