Search:

Type: Posts; User: 5FDP

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    45

    That OS isn't a stock OS, do you have that guys...

    That OS isn't a stock OS, do you have that guys stock file you can reference to see what that says?
  2. Replies
    3
    Views
    59

    Try putting in the tire size of 35's. Putting in...

    Try putting in the tire size of 35's. Putting in overly large tires in the calibration may be why it's setting the ABS light.
  3. Replies
    2
    Views
    62

    Did you do a full read of the PCM/TCM after you...

    Did you do a full read of the PCM/TCM after you hooked up the transmission to the harness.

    When it says general and manual it likely means you haven't fully read the TCM.
  4. Replies
    2
    Views
    81

    Traction control is also part of the...

    Traction control is also part of the ABS/Stabilitrak functions. You can't just turn it off in the tune.
  5. Replies
    6
    Views
    107

    I wouldn't change the maximum allowed knock in PE...

    I wouldn't change the maximum allowed knock in PE because what if it really is greater than 2-4 degrees. Now it can't pull timing away to protect the engine. Leave it at a high number so it can pull...
  6. Replies
    6
    Views
    107

    A pending knock code is usually why the knock...

    A pending knock code is usually why the knock retard will spike up and just stay there.

    Most stock calibrations have the maximum knock at like 8 or 10 degrees. It lets you really see how much...
  7. Replies
    6
    Views
    107

    Do you have a pending knock sensor code at all? ...

    Do you have a pending knock sensor code at all?

    Your knock retard is maxing out at 4 degrees because you set it that way.

    And you can't tune the VE table if the MAF is still working, you are...
  8. Replies
    4
    Views
    106

    We need full details. What MAP sensor is...

    We need full details.

    What MAP sensor is installed?

    What injectors are installed?

    The tune needs work and it seems that there may be the wrong settings in the tune for the MAP he is running....
  9. Thread: Accel Problems

    by 5FDP
    Replies
    1
    Views
    64

    If you want help you need to post your tune and...

    If you want help you need to post your tune and logs.
  10. Thread: Tuner info

    by 5FDP
    Replies
    2
    Views
    63

    Don't expect any tuner to gain you much if any...

    Don't expect any tuner to gain you much if any fuel mileage with a lift. There really isn't any magic that you can sprinkle on it and gain 2-3 miles per gallon.

    HP Tuners uses the OBD2 port, check...
  11. Replies
    6
    Views
    182

    If the table is populated then that's all you...

    If the table is populated then that's all you need to do. The computer is going to pick the correct stoich ratio based on the alcohol content that the sensor sees in the fuel.

    If you use Lambda it...
  12. I've seen a few V6's with high amounts of knock...

    I've seen a few V6's with high amounts of knock like that. I'd make sure all the motor mounts are in good shape and aren't blown out.

    Try making the commanded AFR richer sooner and have it enter...
  13. Replies
    1
    Views
    52

    Is the knock retard channel in the channels list...

    Is the knock retard channel in the channels list on the left??
  14. Replies
    4
    Views
    119

    I want you to find a stock 2003-2007...

    I want you to find a stock 2003-2007 Silverado/Suburban truck file with flex fuel injectors. You should copy the injector data from that tune into your tune so we know it's correct. You need to copy...
  15. Replies
    6
    Views
    182

    Is your stoich table populated with E0 to E100...

    Is your stoich table populated with E0 to E100 values or is the whole table just 14.1??

    Do you have a flex fuel sensor wired in and working so it can read the ethanol percent?
  16. Replies
    6
    Views
    127

    Can you post the tune and logs? Did you do a...

    Can you post the tune and logs?

    Did you do a write entire when you deleted the VATS? Just doing a write calibration only will not disable the VATS.
  17. Remove the 1 bar map channel and replace it with...

    Remove the 1 bar map channel and replace it with the 3 bar MAP channel.

    You must also be running a 2 or 3 bar MAP to read that high too.
  18. Replies
    4
    Views
    119

    What does the gear/tire ratio editor in the edit...

    What does the gear/tire ratio editor in the edit tab say the settings are??


    As for the lean code that could be a number of things. Low fuel pressure, bad tune for the mods on this engine or...
  19. Replies
    3
    Views
    108

    Does it say specifically what controller is not...

    Does it say specifically what controller is not licensed?

    It will usually say something like PCM/E92, T42 or FPSM/FPCM for the fuel pump control module.


    Also I can see it where it if you are...
  20. Looks like it's dipping into COT enrichment too,...

    Looks like it's dipping into COT enrichment too, making the commanded fuel too rich. I would set that much lower and only rely on the PE EQ ratio for commanded fueling.

    I would also zero out the...
  21. Replies
    17
    Views
    876

    You wouldn't be able to view the tune file if it...

    You wouldn't be able to view the tune file if it was tuner locked. Simple as that.
  22. Thread: is mpvi required?

    by 5FDP
    Replies
    9
    Views
    518

    Forever tied. You are paying to unlock the...

    Forever tied. You are paying to unlock the computer and you are allowed to do basically unlimited changes for whatever credit amount that initial credit amount was.

    $100 is pretty cheap for doing...
  23. Replies
    1
    Views
    101

    What kind of vehicle do you have?? I can tune...

    What kind of vehicle do you have??

    I can tune many vehicles with my laptop in a parking lot without internet.
  24. Replies
    2
    Views
    72

    Should be able to click the layout at the top on...

    Should be able to click the layout at the top on the scanner and then down to default layouts. Just pick which one you want as the default.

    You can right click the channels list on the left and...
  25. Thread: Will it run

    by 5FDP
    Replies
    3
    Views
    66

    A license is a one time cost for credits. Once...

    A license is a one time cost for credits. Once you license the computer you can make an unlimited amount of changes.

    You can buy the standard MPVI2 if you want. Just know that it will make putting...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4