Search:

Type: Posts; User: 06300CSRT8

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    70

    that cam will not idle at that low of RPM. I...

    that cam will not idle at that low of RPM. I wouldn't try to idle it any lower than 800 or so. Raise your Low Idle rpm setting to 700 and make the rest of the idle set points be 800 or so. Make...
  2. Replies
    3
    Views
    49

    Without the tune, impossible to really help. I...

    Without the tune, impossible to really help. I totally respect you not posting it (and shouldn't) but hopefully you have given this to the tune provider to try and fix.

    If Neural network is still...
  3. Clearly taking 19psi of fuel pressure out of my...

    Clearly taking 19psi of fuel pressure out of my system will bring the fuel delivery way down. Not looking to do that.
  4. Yes, regulator is boost and vacuum fed, my vacuum...

    Yes, regulator is boost and vacuum fed, my vacuum multiplier table is all 1?s
  5. Return Style System with ID1300 - WOT Fueling WAY OFF

    So I am using ID data for the ID1300x2 that I have (I realize there is now newer data, but its not that much difference).

    I have a dual 450lph Fore pump, 10an feed, 8an return, Aeromotive 1000...
  6. Replies
    8
    Views
    139

    No, been running a Ding's VB since trans was new....

    No, been running a Ding's VB since trans was new. That said I do have the original Paramount valve body I could switch in, just the drivability is pretty horrid outside of WOT. Like getting hit...
  7. Replies
    8
    Views
    139

    Issue I have with it being mechanical is it acts...

    Issue I have with it being mechanical is it acts the same at half the horsepower. Doesn't seem power related, i.e. mechanically related to the clutches slipping. Guessing has something to do with...
  8. Replies
    8
    Views
    139

    Ah ha, you are correct! clearly can see its...

    Ah ha, you are correct! clearly can see its slower polling.

    But regardless, back to the original question, shift is commanded at 6500 rpms, I can see it commanding a shift starting right around...
  9. Replies
    8
    Views
    139

    Yes. But not showing in the engine RPM, only in...

    Yes. But not showing in the engine RPM, only in trans RPM
  10. Replies
    8
    Views
    139

    Trans Turbine RPM Spike, RPM Limit

    I trying to figure out what to change in my TCM tune to eliminate a Trans Turbine RPM spike on my shifts that causes me to tap the rev limiter, close the throttle and cut fuel. You can see the...
  11. Replies
    11
    Views
    1,145

    You have to combine the apply/release settings...

    You have to combine the apply/release settings with the TCC Desired slip to get it to slip by RPM. you can set it to lock but still have some slip until a given output shaft rpm. Setting the...
  12. Boot loader is messed up, when you bought a "new"...

    Boot loader is messed up, when you bought a "new" pcm was it rebuilt or new new?

    Have had this happen a few times switching being tuning companies (diablo to HP, Syke to HP).
  13. My suspicion of a fried PCM is a very weak...

    My suspicion of a fried PCM is a very weak ignition, which the coils are seemingly going intermittently firing and not able to recover under any amount of cylinder pressure.

    On first fireup, I...
  14. Replies
    3
    Views
    241

    Thanks guys

    Thanks guys
  15. Replies
    2
    Views
    107

    was told yes, I have it, but have not tried it yet

    was told yes, I have it, but have not tried it yet
  16. Need a new ECU for my 2014 Chrysler 300 SRT

    Pretty sure i fried some or part of the ECU when i crossed some wiring on my sensors. To rule out the ECU as the cause, I want to replace it. But not sure the exact procedure and what tools I need...
  17. Not a good idea on the NGC3. Unlike the GPEC, in...

    Not a good idea on the NGC3. Unlike the GPEC, in my experience no matter what you do, you will exceed a hard coded airflow limit based on actual Map readings if you leave it enabled. The result is...
  18. Replies
    2
    Views
    158

    youll have to filter your log for when you are...

    youll have to filter your log for when you are full throttle, that 20 degrees is probably only on decel
  19. Its a combination of microphone and has a logging...

    Its a combination of microphone and has a logging box/laptop connection with its own software.

    I didn't prove any of your point. You continue to tell us that the stock knock floor doesn't work,...
  20. I purchased a knock box and it was EXTREMELY...

    I purchased a knock box and it was EXTREMELY helpful, strongly suggest you stop "knocking" (pun intended) on using one. Stock knock sensors were reporting high voltages, knock box with headphones I...
  21. I don't want to steer you wrong, i have little...

    I don't want to steer you wrong, i have little experience tuning 8 speeds (yet).
  22. Thread: idle

    by 06300CSRT8
    Replies
    1
    Views
    127

    No one is going to help you with so little...

    No one is going to help you with so little information, no tune, no log, no engine info.
  23. Replies
    2
    Views
    152

    Pressure Ratio is a built in math parameter, it...

    Pressure Ratio is a built in math parameter, it is not actually in the ECU. Most likely for some reason your particular ECU doesn't have one of the two SAE PIDs the math is expecting (barometric...
  24. Replies
    4
    Views
    138

    Gotcha - wouldn't worry too too much about it,...

    Gotcha - wouldn't worry too too much about it, but for sure that is the correct table to play with to get it to run richer on cold starts.
  25. Youre tuning with ANN enabled, so saying you...

    Youre tuning with ANN enabled, so saying you "tuned the VE" makes no sense since the VE tables aren't used. You need to pull fuel out by tweaking the injector tables. Its running rich, simple as...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4