Search:

Type: Posts; User: dhoagland

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. So if I understand correctly everything works...

    So if I understand correctly everything works fine so long as you have your Prolink connected?
    I understand that shouldn't happen, just curious if I run into this problem you have discovered a...
  2. This was over a year ago and with mpvi1 So not...

    This was over a year ago and with mpvi1 So not sure if its relevant anymore.

    Read and flashed an 03 without issue, a month or so later tried an 04... It let me read (or so I think it did) but when...
  3. Thread: LML Tunes

    by dhoagland
    Replies
    3
    Views
    441

    My experience with your question is from an LB7,...

    My experience with your question is from an LB7, but I think the answer is relevant...

    I did a few Tunes for son in law for his edge insight.
    It worked but he was disappointed in the fact that...
  4. Replies
    1
    Views
    284

    https://forum.hptuners.com/showthread.php?75715-An...

    https://forum.hptuners.com/showthread.php?75715-Any-Actual-Need-For-Pilot-Injections-Other-Than-Cold-Weather-Cold-Starts

    Here are a few threads with some good info/ideas.
    I know its not Ford, but...
  5. Replies
    12
    Views
    591

    I don't have a channels list for the D-Max......

    I don't have a channels list for the D-Max...
    Maybe someone else will have an idea
  6. Replies
    12
    Views
    591

    Can you scan and see what is "Torque Limiting" or...

    Can you scan and see what is "Torque Limiting" or "Fuel limiting" ??
    In my 03 Cummins they have "Master Fuel Correction" and "Final timing Correction"
  7. Replies
    12
    Views
    591

    Not positive on the flow rates, but don't think...

    Not positive on the flow rates, but don't think so>
    I installed some 30% oversize in an LB7 (with an aftermarket turbo) and it ran just fine without modification. It smoked/hazed at idle and when...
  8. Replies
    7
    Views
    360

    Glad you found it. Things like that can be a...

    Glad you found it.
    Things like that can be a bear to find, and are easy to overlook.
  9. Have you tried re-reading the truck? Does the...

    Have you tried re-reading the truck?
    Does the scanner function?
  10. I think this is the latest Timing calculater

    I think this is the latest Timing calculater
  11. Replies
    7
    Views
    360

    You should be able to scan for what is limiting...

    You should be able to scan for what is limiting your torque/fuel...

    In the Cummins (03) Its "Master fuel correction reason"...

    Couple of observations:
    In your scans your relative throttle...
  12. Replies
    7
    Views
    360

    Rookie tuner here. But from my past experience...

    Rookie tuner here.
    But from my past experience in these situations you need to completely remove your edge programmer. Not just set it to stock power, completely remove it.

    I had an 03 Cummins...
  13. Replies
    10
    Views
    917

    03 Excursion, "yyyyyyyyyy" hardly any parameters...

    03 Excursion, "yyyyyyyyyy" hardly any parameters available to scan..
  14. Replies
    2
    Views
    294

    What codes are being set?

    What codes are being set?
  15. https://forum.hptuners.com/showthread.php?75559-pi...

    https://forum.hptuners.com/showthread.php?75559-pilot-enabled-warm-up

    There are some discussions in the Cummins section of the forum on single event tuning, might get you headed in the right...
  16. Replies
    10
    Views
    583

    Hey Jim Would the timing calculator work for...

    Hey Jim

    Would the timing calculator work for him with a single event tune?
  17. Replies
    1
    Views
    400

    03 Tuning

    Pretty good discussion in this one
    https://forum.hptuners.com/showthread.php?68465-2003-5-9HO-Tune-Review

    This thread is pretty informative, I got a lot out of comparing it to stock....
  18. Replies
    3
    Views
    609

    Layout

    Something like this?
  19. Replies
    3
    Views
    502

    Maybe Max Boost EGR off? 82397

    Maybe Max Boost EGR off?
    82397
  20. Maybe throw a big vacuum leak at it and see if...

    Maybe throw a big vacuum leak at it and see if they come down?
  21. Replies
    1
    Views
    226

    I'm new to F150, I'm chasing an issue...

    I'm new to F150, I'm chasing an issue myself...Mine would not get out of its own way...
    Look at your Boardeline spark table, if your at full load range and low RPM it will pull all your timing in...
  22. Replies
    7
    Views
    823

    Me too

    Me too
  23. Replies
    1
    Views
    349

    I'm a noob, so take what I say with that in mind....

    I'm a noob, so take what I say with that in mind.
    I believe most will tell you to leave idle areas basically stock, Unless you have crazy oversize nozzles.

    Completely different platform. On my...
  24. Replies
    2
    Views
    546

    You are in the Diesel section (I'm assuming the...

    You are in the Diesel section (I'm assuming the 2.8 isn't diesel)

    I found the tutorial in this link to be a very good guide that should adapt to your platforms, and they will answer questions you...
  25. Replies
    3
    Views
    502

    I'm a noob at HP Tuners...But if you look at...

    I'm a noob at HP Tuners...But if you look at Engine, Torque Management, SC/TC Boost control. I believe these are fuel limiters based on boost PSI most likely for smoke control.
    2 other tabs in...
Results 1 to 25 of 35
Page 1 of 2 1 2