Search:

Type: Posts; User: Mbrowning

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    255

    If you can upload the file, it should be easy to...

    If you can upload the file, it should be easy to spot. If you are running a gen v OS, then the problem is most likely the DD tables.
  2. It bypasses the vehicle communication interface,...

    It bypasses the vehicle communication interface, which is required for their scan equipment to check your vehicle and update as needed. If you don't take it out, they most likely will (and charge you...
  3. Replies
    9
    Views
    1,068

    You can get in trouble quick with those tables....

    You can get in trouble quick with those tables. That's why they warn you to change them at your own risk. If you increase the ENTIRE table by 5 or 10 percent. It makes the entire vehicle react...
  4. Replies
    9
    Views
    1,068

    On the driver demand tables, highlight the WHOLE...

    On the driver demand tables, highlight the WHOLE TABLE and multiply by 1.1. Tables A and C are the ones to modify.
  5. Replies
    9
    Views
    1,068

    I touched up your file to give you some stuff to...

    I touched up your file to give you some stuff to look at. I learn a lot looking at changes and researching the definitions and noting changes. The changes I made are the same ones I use in my 2017...
  6. Replies
    9
    Views
    1,068

    I recommend going to discrete shift mode and...

    I recommend going to discrete shift mode and disable the 2-3. 1 is enabled, 0 is disabled. Next, to firm up the shifts, go the the shift timing tab, then torque adder. These are the tables that add...
  7. Good point ZincGT. I had hoped to find a lost...

    Good point ZincGT. I had hoped to find a lost Ford tuner looking for LS help. This was all a total waste of time really. I am going to close this on a good note. If there is anyone stuck on a GT350...
  8. Works for me. I was looking for a Ford tuner that...

    Works for me. I was looking for a Ford tuner that needed a LS tuner. Guess I should have rephrased my question. However, that does not excuse your condescending attitude. Move along please because as...
  9. In the future, save your opinion for someone that...

    In the future, save your opinion for someone that wants it, mbray01
  10. Replies
    3
    Views
    397

    Just an update. I solved my problem with a custom...

    Just an update. I solved my problem with a custom table that works really well with driver demand. Case closed. Thanks everyone.
  11. My main concern was the throttle body. The...

    My main concern was the throttle body. The customer had a 2016 GT 5.0 with a 5.2 voodoo intake ant gt350 throttle body. The math is WAY DIFFERENT for the two. After about six hours of math and...
  12. OK...i'll start with VCT

    OK...i'll start with VCT
  13. I'm looking for a Ford guy with LS problems.

    I'm looking for some help with a 2016 mustang 5.0 in trade for some help with LS. Any takers?
  14. Replies
    3
    Views
    397

    2016 Mustang GT tuning questions

    Hello everyone. I have a 2016 Mustang GT with a CAI, 5.2 voodoo intake, and gt 350 throttle body. Not my car personally but one that was offered to me as a learning tool. I've had good success with...
  15. Replies
    10
    Views
    937

    That's awesome and all, but you can still tune a...

    That's awesome and all, but you can still tune a truck ahem, "correctly" and still make the driver demand table more responsive. The tables mentioned affect more than just the engine and transmission.
  16. Replies
    10
    Views
    937

    Any or all four. Modify the ones you want to...

    Any or all four. Modify the ones you want to respond more aggressively.
  17. I haven't logged to know for sure. Actually, it's...

    I haven't logged to know for sure. Actually, it's most likely redundant to disable rate limits if you max the tables out. If I remember, at first there was not a disable option. I think it was added...
  18. Replies
    10
    Views
    937

    Take table "A" and table "C" and modify this way....

    Take table "A" and table "C" and modify this way. Highlight the entire table and multiply by 1.05. This adds 5 percent to the entire table. The first instinct is to look at the bottom half of the...
  19. 95990 If you open your file in the beta...

    95990

    If you open your file in the beta version, you will see immediate and predicted torque increase. Make sure they are maxed out. Disable torque request rate limit. This was some code that GM...
  20. Replies
    54
    Views
    111,315

    I'm messing with 4.5 beta. Some direction would...

    I'm messing with 4.5 beta. Some direction would be nice. These gen v's are tough. So many pid's need to be polled.
  21. I the last few I tuned, I used the Blue Cat...

    I the last few I tuned, I used the Blue Cat software to set up my tables. There are some videos on youtube showing how to use them. Good stuff.
  22. Replies
    6
    Views
    339

    Probably wouldn't hurt to check your connections...

    Probably wouldn't hurt to check your connections at the MAF sensor. This looks like a good time to invest in a wideband if you don't already have one. Something's obviously not reading right.
  23. It took a minute, but I think I found it. Your...

    It took a minute, but I think I found it. Your vve table looks jacked up for some reason. Looks like someone was tuning and quit halfway through. A table that rough is going to cause you all kinds of...
  24. Replies
    11
    Views
    1,051

    1-2 flare correction

    Here you go brother...
  25. Replies
    9
    Views
    772

    giffincox, normally when the blade is wide open,...

    giffincox, normally when the blade is wide open, PID will show 89% for some reason.
Results 1 to 25 of 70
Page 1 of 3 1 2 3