Search:

I need to delete pats on a 2002 mustang 4.6. The vehicle list shows mpvi3 will not read/write. Is that correct?

The Pcmofnc harness is very easy to use and works good.

Thanks.

I have a customer wanting dod delete programming on a 2018 silverado. The truck still has stock cam and lifters. I see it takes more credits than earlier gen5. Is it still as simple as just turning...

There is a 9.5 14 bolt option that’s bolt in for that truck. They are pretty reasonable at a salvage. I’d either go with it or a 9”. Either one is way stronger than a 10 bolt. I’ve also used a full...

I ended up using the harness.It worked great.

I made the changes to pe and timing. I also logged injectors and knock retard. It did show some spark retard. Do I lower the spark tables by the amount of retard it shows? The tcc shows slip when the...

Here are the data logs. Thanks for telling me how to get the data log to load.

I can't get the data log to upload. Is there a limit on the size or something?

I have a 2010 sierra 1500. Factory 4.8 4l60e. Installed a l96 6.0 from 2014 2500 and a 4l80e out of a 2005. I used the pcm of nc 4l60 to 4l80 adapter harness. The motor has a texas speed vvt stage 1...

Looks like a lot of the lights that are on and what?s not working is on splice pack sp300. See if you can communicate with any module on the splice pack. Any of the modules can short out and make...

Are you sure the code is u0241 and not u0214. U0241 shows to be for Headlamp Control Module, u0214 is for rfa. Can you communicate with air bag, object detection, lift gate, seat heater modules?

Need to scan all modules and see what codes they have.

Got it going. Disabled vats 1 and 2 and start permission

How does the vats patch work? Do I need to do 1 and 2 or just one of them? 2008 sierra 1500

Will this work with a pcm that’s set up on serial data for a/c a few of the wires the diagram shows was not used on the factory harness.

Here is the file. This is a 6.0 in a 1985 c10. The a/c is on all stock for the truck other than a sanden compressor. Has aftermarket dual fans on separate relays. I would like to be able to idle the...

I have gen 3 ecm 12589463. Is there a wire to run 12v from the compressor to help the truck idle with a/c on or will I have to install a pressure switch and relay. The only wires I see are pin 43 ...

I don’t see how it could be the tune. The mds delete is pretty straight forward. We do a lot of deletes on gm and Chryslers and do delete tunes for some other shops. Every time there is a problem...

I figured out how to adjust the gauge itself. Just need to read directions a few more times

I went ahead and put a set in an 85 c10. They look really good. Haven’t had them on the truck very long but satisfied so far.

Does changing the pcm output calibration pulses per mile only change the pulse output on the speedometer signal wire. Can I change it to get an aftermarket speedometer reading right? Does it effect...

Thanks for the link. I have a 4l80 out of a 98 Chevy with a 350. I know it doesn’t have the top center bellhousing hole but is there anything that would keep it from working. Would it have to be from...

I have a 2010 Sierra that came factory with a 4.8-4l60e. Installed a l96 6.0 with stage 1 tsp cam kit with a billet 2600 converter. The transmission shifted fine with 4.8 but would not hold in 2nd...

Just wondering if anyone has used glowshift gauges. They look really nice and are priced good but i have no idea about their quality.