Search:

Type: Posts; User: dr.mike

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Close... I had eye surgeries on both eyes, over...

    Close... I had eye surgeries on both eyes, over the last year ( vitrectomies and cataract lenses ), . I am "mostly recovered". But, it is, still, difficult for me to do programming work. It is...
  2. OK. Sorry again about the extended absence. I...

    OK. Sorry again about the extended absence. I had multiple eye surgeries, on both eyes. They are letting me get back to work, now.
  3. Sorry, all. Been dealing with some medical...

    Sorry, all. Been dealing with some medical issues. I hope to be back to it, soon.
  4. I cleared some space :) I was able to grab...

    I cleared some space :)



    I was able to grab an PCM from a 4.7L V8 Durango. That should do it, at least for the JTEC stuff.
  5. Replies
    20
    Views
    1,828

    06 Silverado has a pre-CAN ECU. The 30-0334 only...

    06 Silverado has a pre-CAN ECU. The 30-0334 only works with CAN based ECUs. Usually, 2007 or later.
  6. It is, mostly the same firmware as the 30-0334. ...

    It is, mostly the same firmware as the 30-0334. But. it has no user interface/display. So, if you want more than 1 wideband, you need to order them preprogrammed as #1, #2, etc.
  7. Try doing an info log to see what all is in there.

    Try doing an info log to see what all is in there.
  8. It should show up as "WB EQ Ration 1 (SAE)" It...

    It should show up as "WB EQ Ration 1 (SAE)"
    It does not show up in the "X-Series UEGO ( 30-0300 )" section. That is for widebands that are connected via the ProLink.
  9. What is the vehicle ?

    What is the vehicle ?
  10. Replies
    7
    Views
    1,234

    If you have the MPVI3, the best way to go is the...

    If you have the MPVI3, the best way to go is the AEM 30-0300 ( not 30-0334 ) , with the ProLink, via the ProLink CAN interface ( not the OBD2 CAN, which your PCM does not have ).
  11. Looked on eBay. Those look kinda pricey, in case...

    Looked on eBay. Those look kinda pricey, in case it were to get damaged, in the process.
  12. PM me.

    PM me.
  13. Replies
    14
    Views
    7,400

    The 30-0300 and 30-0334 use two different...

    The 30-0300 and 30-0334 use two different protocols.

    The 30-0300 uses AEMNet protocol. It can be read by the ProLink CAN inputs. And the data shows up in the AEM section.

    The 30-0334 uses...
  14. But, while on the subject of Chrysler...

    But, while on the subject of Chrysler products,does anyone know what ECU I can get, that I can get the pinouts for, so that I can run it on my test bench?

    My ECU simulators do GM and Ford. But,...
  15. If you have a prolink, you should be able to...

    If you have a prolink, you should be able to connect the wideband via CAN.
  16. Replies
    5
    Views
    1,191

    If you are using the MPVI3, with the ProLink, you...

    If you are using the MPVI3, with the ProLink, you can use CAN on any vehicle.
    The ProLink CAN interface connects, directly, to the AEMNet CAN lines on the 30-0300/30-0310 wiring harnesses.

    In...
  17. Not quite all. There is an ISO-9141 protocol,...

    Not quite all. There is an ISO-9141 protocol, used, mostly by pre-CAN Japanese vehicles. It is, actually, one of the easiest protocols to cover. I had to drop it, in order to save room on the PCB....
  18. Not with the 30-0334. But, rather, instead of...

    Not with the 30-0334. But, rather, instead of the 30-0334. i.e. it works with the original 30-0300 and/or 30-0310. But, instead of providing an OBD2 interface, only for CAN based vehicles, like the...
  19. For the TL;DR crowd :p This box is an OBD2...

    For the TL;DR crowd :p

    This box is an OBD2 "piggyback" ECU that serves up custom PIDs, as if it were part of the stock vehicle's data bus. It is a pass-thru connector that goes between the...
  20. I can probably send units out on Monday.

    I can probably send units out on Monday.
  21. Beta prototype units are ready !

    OK. These are as ready as they are going to get. Everything is working as designed, on the test bench.

    I am looking for the 1st 3 testers. Ideal candidate is someone who:


    is using the AEM...
  22. Which Dodge/Chrysler/Plymouth ( and Jeep ? ) ...

    Which Dodge/Chrysler/Plymouth ( and Jeep ? ) applications are people interested in adding support for?
    I am going to have to grab a couple of PCMs off of EBAY and Frankenstein them back to life on...
  23. OK. I am back online :) I tested out the new...

    OK. I am back online :)

    I tested out the new prototypes. They look good so far. I am ready to take on a few new testers. Starting with GM 1996-2006. Then Ford.

    Chrysler is going to be a bit...
  24. I should be ready to send out a new batch of test...

    I should be ready to send out a new batch of test units, early next week.
  25. With all the COVID nonsense ( including my...

    With all the COVID nonsense ( including my production guy having COVID ), I JUST NOW got the A3 rev PCBs in.
    I should have a few test units available this week.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4