Search:

Type: Posts; User: rcodea1

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. TorqueRush X2 Dual DBW Throttle Controler

    Has anyone used the x2 and willing to share some helpful hints? I am just starting the to delve into the software and process for tuning it. My goal is to allow the second throttle to remain closed...
  2. Replies
    14
    Views
    3,613

    does anyone know if this also applies to the TCM...

    does anyone know if this also applies to the TCM OS 24267577...that is what is on my '14 Caprice PPV...doesnt match the others posted, but i seem to have the same issues

    ~Ryan
    Charleston, SC
  3. Replies
    0
    Views
    86

    Dual 90mm DBW tuning

    Hello all, I am in the process of getting my blower onto the 6.0l using the e38 PCM. I will be running dual 90mm LS3, using the TorqueRush X2 controller. It will essentially a mirror box...matches...
  4. Replies
    7
    Views
    957

    95012 for reference here is my '14 Caprice trans...

    95012
    for reference here is my '14 Caprice trans tune. I didnt change anything in the trans section, so it may be of use for comparison for you. When i compare this to a ZL1 or LSA car, it seems...
  5. what was the resolution on this? I too would like...

    what was the resolution on this? I too would like to know how to get the e38 to run a PWM fuel pump without the stock FPCM.
  6. Replies
    7
    Views
    957

    my '14 caprice swap has similar issues....TCC...

    my '14 caprice swap has similar issues....TCC line pressure will show up and down, but i still get slip. Looking forward to this discussion as well.

    was this also an issue before the cam swap?
    ...
  7. Replies
    3
    Views
    285

    Anyone have any thoughts or ideas whom I can turn...

    Anyone have any thoughts or ideas whom I can turn to for information like this?

    ~Ryan
    Charleston, SC
  8. Copy Russ, thank you!

    Copy Russ, thank you!
  9. Bump for the above question....with the STFT...

    Bump for the above question....with the STFT turned off for feedback, can the sensors be run and installed without causing damage to them?
  10. Worked and did not report STFT or LTFT into the...

    Worked and did not report STFT or LTFT into the commanded fuel. Thank you for the help!

    Last question....can the NBO2 sensors be connected and run withiut causing damage using these settings? I...
  11. done. will report when i can get back on the...

    done. will report when i can get back on the roads with this storm.

    this is not a perameter i have changed in the past, but only now am getting it to kick in. Why is it suddenly wanting to kick...
  12. STFT suddenly impacting tune on Open loop base tune

    Hello all, thanks in advance for the help. engine is a 9.6 CR LS2 out of a '14 Caprice PPV with 823 heads, BTR stg 2 PDS cam, mid headers and 3" exhaust, backed by a 6L80e running on the stock e38...
  13. also found that it is reacting the same way when...

    also found that it is reacting the same way when i connected to my ATS...so its something with the scanner and not the truck. so i guess i'll just press
  14. neg, 4.4.4 did not correct it. i'll have to take...

    neg, 4.4.4 did not correct it. i'll have to take a video of it...the log itself, doesnt show it.
  15. I'll try that and report back.

    I'll try that and report back.
  16. Erratic TSP signal and strange Brake Applied status, Gen 4 MPVI2 4.4.2

    Seems I am having two odd readings which I think are software related to Scanner 4.4.2, but I can?t think of a way to confirm.

    The first, when logging tsp position, KOEO, the signal bounces...
  17. Replies
    45
    Views
    2,253

    looking for some help here....still..... I am...

    looking for some help here....still.....

    I am trying to get this brake pedal position switch to work properly. Basically, the current setup works when the KOEO, but once the engine starts, I get...
  18. Replies
    45
    Views
    2,253

    i honestly stopped looking at the dtcs once i got...

    i honestly stopped looking at the dtcs once i got the MAP to work correctly and the MAF to fail. I'll clean that up tonight.

    I have left the Flex Fuel code specificly to remind me to install...
  19. Replies
    45
    Views
    2,253

    no, my foot was not riding the brake...it seems...

    no, my foot was not riding the brake...it seems to have to do with the wiring harness and the instructions i was given. at present, there are two purple wires going to the 12V switched wehn brake is...
  20. Replies
    45
    Views
    2,253

    made those changes and got the truck on the road...

    made those changes and got the truck on the road for the first time. seems to be ok when i am gentle on it around the neighborhood. however, the commanded is still showing .86 lambda or 12.5 AFR...
  21. Replies
    45
    Views
    2,253

    copy. i was going to mention that the lambda vs...

    copy. i was going to mention that the lambda vs AFR point makes since, but my question was more on what is causing it to command a 0.85 vs 1.00 as i was setting up in the tables. the run time you...
  22. Replies
    45
    Views
    2,253

    i made the adjustments to the open loop gas in...

    i made the adjustments to the open loop gas in both pn and gear, and i am still getting a commanded of ~12.5 when idling. at this point i am thinking of just leaving it and letting the tuner figure...
  23. Replies
    3
    Views
    471

    so accross years it worked ok...anything...

    so accross years it worked ok...anything additional with your tune or wiring needed as well? I have noticed that there is a 5v coming to my pedal from the actermarket wiring harness...as well as the...
  24. Replies
    45
    Views
    2,253

    copy, i knew i was missing something. I'll make...

    copy, i knew i was missing something. I'll make the change and give it a try tonight. I was trying to get to the point of VE set to stoich across the light cruising range, safe enough to make it to...
  25. Replies
    45
    Views
    2,253

    ok looking for some honest help here. trying...

    ok looking for some honest help here.

    trying to figure out how to change the 'AFR Commanded'. I have my histogram working for AFR Error and such. no issues there. But trying to change the...
Results 1 to 25 of 59
Page 1 of 3 1 2 3