Search:

Type: Posts; User: tpickrem

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    479

    E38 dfco will not disable

    Hey guys,
    I?m hoping you can save me from this headache. E38 ecu (2014 camaro w/ ls3 and 6 speed manual) I cannot for the life of me get DFCO to turn off. I?ve tried using the temperature...
  2. Replies
    8
    Views
    2,292

    So to update, I have verified the wiring to the...

    So to update, I have verified the wiring to the iac is correct and the ecm definitely has the iac drivers.

    I can control the iac with the scanner only when the key is on but the engine is off. Is...
  3. Replies
    8
    Views
    2,292

    The ecm came out of a drive by cable van and i...

    The ecm came out of a drive by cable van and i can manually move the iac using the scanner special functions. I?ll double check the ecm to make sure but I?m fairly certain it has drivers
  4. Replies
    8
    Views
    2,292

    I do have the wires swapped but I?ll triple check...

    I do have the wires swapped but I?ll triple check they are pinned correctly



    Thanks for pointing that out, I had changed that in the subsequent tune but put this one back in and forgot I hadn?t...
  5. Replies
    8
    Views
    2,292

    4.8 LS swap IAC not moving

    Hi guys,

    I am working on a 56 cadillac with a 4.8 4l80e combo. The engine is stock except for a holley 300-137 single plane intake and matching 112-588 4 bbl throttle body. the car will start and...
  6. Replies
    6
    Views
    1,301

    Would I be better off using a truck 6.0L manual...

    Would I be better off using a truck 6.0L manual tune? Since the camaro is 5.7L?
  7. Replies
    6
    Views
    1,301

    thanks Ben! will any red blue ECM work? or am...

    thanks Ben!

    will any red blue ECM work? or am I limited to finding one from a camaro
  8. Replies
    6
    Views
    1,301

    DBC 6.0L with tr6060

    Good morning everyone,
    I am looking for a solution to my problem. I am building an LSA supercharged 6.0L (LQ9) for my 1956 chevy bel air and I am having trouble deciding which way to go. I need to...
  9. Replies
    1
    Views
    828

    ls3 6 speed stalls

    ls3 camaro stalls when clutch is pressed. mods are limited to cold air intake. any input is appreciated

    tune file: 114124
  10. Replies
    4
    Views
    1,167

    Thank sir! This was indeed the problem. How do...

    Thank sir! This was indeed the problem. How do the harnesses get swapped end to end?
  11. Replies
    4
    Views
    1,167

    bump

    bump
  12. Replies
    4
    Views
    1,167

    Cammed LQ4 first start backfires

    Hey guys,
    I finally got to start my LS swapped Chevelle. It's a cammed LQ4 (231/235 at 0.050 and .626/.605 lift) with 243 heads milled 0.020" and ported. Victor Jr intake with a holley 4150 style...
  13. Replies
    5
    Views
    1,220

    is there anything additional that needs to be...

    is there anything additional that needs to be done to make the computer know its in SD mode? I was reading about people having trouble with first start because the vehicle was trying to start with...
  14. Replies
    5
    Views
    1,220

    here is the tune file109598

    here is the tune file109598
  15. Replies
    5
    Views
    1,220

    I actually had you look it over a month or two...

    I actually had you look it over a month or two ago but I?ll post it up again! Unfortunately the car itself isn?t quite finished yet so I can?t actually drive it. I don?t plan on dialling the idle in...
  16. Replies
    5
    Views
    1,220

    Bump

    Bump
  17. Replies
    5
    Views
    1,220

    LS swap Chevelle first start

    Hey guys,
    I?m getting ready to start my 70 Chevelle LS swap for the first time. I?ve done a couple other swaps but nothing where this much has been changed. This car has a different cam, heads,...
  18. Replies
    5
    Views
    2,295

    How does the computer decide between high and low...

    How does the computer decide between high and low octane tables? It seemed a little odd to me that they would make the base timing higher than an N/A setup even with the temp tables pulling timing.
  19. Replies
    5
    Views
    2,295

    LSA tune... what is going on here

    Hey guys,
    the tune i'm about to post is from a car I'm storing for a buddy of mine. It's a 2014 camaro zl1 with an LSA. I'm new to tuning so I decided to scan his car and see what the tune looked...
  20. Replies
    7
    Views
    4,083

    thats good to hear! is there anything else...

    thats good to hear!
    is there anything else obvious that I'm missing?
  21. Replies
    7
    Views
    4,083

    So there?s no issues with the data being off by a...

    So there?s no issues with the data being off by a slight amount? How does the VE table look after the changes?
  22. Replies
    7
    Views
    4,083

    i'm also going to post the injector data 104388

    i'm also going to post the injector data 104388
  23. Replies
    7
    Views
    4,083

    ok so I tried to input the injector data supplied...

    ok so I tried to input the injector data supplied by deatschworks but every time I put it into the table it changes when I press enter. I also changed the VE table back to stock except I removed some...
  24. Replies
    7
    Views
    4,083

    6.0L base tune

    hey guys,
    I'm relatively new to tuning and I'm working on my first swap. It's a 2005 6.0L going into my 1970 Chevelle.
    The engine:
    stock bore 6.0L
    ported 243 heads milled 0.020 (should be...
Results 1 to 24 of 24