Search:

Type: Posts; User: DB5249

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    688

    everything needs to be in working order, check...

    everything needs to be in working order, check and fix any codes. send me a log file if you will
  2. Replies
    20
    Views
    688

    download the and use both the graphs and channels...

    download the and use both the graphs and channels I sent you earlier in the post
  3. Replies
    20
    Views
    688

    you can drop the idol down, just keep it where it...

    you can drop the idol down, just keep it where it won't stall, you can usually get away with 800 rpm
  4. Replies
    20
    Views
    688

    119538

    119538
  5. Replies
    20
    Views
    688

    after you get the hang of that, since you are...

    after you get the hang of that, since you are using a partial cam phase, in the future focus on how to do a neural network tune, essentially a VE table for each cam angle range, you will have to set...
  6. Replies
    20
    Views
    688

    that should get you started, use the LTFT + STFT...

    that should get you started, use the LTFT + STFT GRAPH, its based on fuel percentage on fuel trims, you can copy all data in the graph and then go to your ve table1 in the speed density section,...
  7. Replies
    20
    Views
    688

    119536 119537

    119536

    119537
  8. Replies
    20
    Views
    688

    yes but i can send you a basic graph and log...

    yes but i can send you a basic graph and log channels
  9. Replies
    20
    Views
    688

    i always recommend using a wideband gauge to...

    i always recommend using a wideband gauge to verify fueling and logging it to vcm scanner, your truck used EQ ratio Lambda, so you will want to make a graph utilizing eq error ratio math and in...
  10. Replies
    20
    Views
    688

    just pull the revised file i sent you upload it...

    just pull the revised file i sent you upload it and try to start the truck, it will be rich at first start so you might have to help it run giving it a little throttle until it learns the throttle...
  11. Replies
    20
    Views
    688

    if you don't have a cam phase limiter installed...

    if you don't have a cam phase limiter installed it could have caused you to bend valves or interfere when it pulls back to fuel on the exhaust cam phase, retard. these engines only use the exhaust...
  12. Replies
    20
    Views
    688

    well there is a lot off in the tune, especially...

    well there is a lot off in the tune, especially if you don't have a cam phaser limiter installed
  13. Replies
    2
    Views
    585

    119520 119521

    119520

    119521
  14. The engine was a fresh build, after i got the...

    The engine was a fresh build, after i got the truck running it was miss firing, bank 2 showed it in the stft, rich compared to bank one, pulled out the handy dandy snap off scanner pulled pids on...
  15. i will do a neural network tune for him later...

    i will do a neural network tune for him later logging each cam phase angle vs ve in graphs, just trying to get it going. I appreciate the verified information
  16. Neural Network will be disabled, cant get a data...

    Neural Network will be disabled, cant get a data log if the truck won't run more than a few seconds. i already had to fix the can wires between C123 and C130 just to get it to read ecm. its an...
  17. all I want is injector data. Its a friend's...

    all I want is injector data. Its a friend's truck. he already has the 6.4 intake on his truck as well. in order to use the stock injectors in the 6.4 intake he needs injector shims. no real reason he...
  18. 2010 Ram 5.7 with a 6.4 intake and injectors. Need help calibrating fuel injectors

    I have a 2010 Ram 5.7 with a cam and a phase limiter,
    runs rich and won't stay running,

    this should be a common swap but I need to calibrate the (0 280 158 310) injectors.

    I tried comparing...
  19. Replies
    2
    Views
    475

    here is a Starting base for graphs

    here is a Starting base for graphs
  20. Replies
    2
    Views
    475

    Desired Lambda, Rpm Coolant Engine Load...

    Desired Lambda,
    Rpm
    Coolant
    Engine Load
    Exhaust gas temp
    Injector Pulse Width
    Throttle position sensor
    manifold absolute pressure kpa
    barometric pressure
    accel pedal position
  21. Replies
    2
    Views
    585

    EQ Error Math Come get it.

    100 * ([50119.238] - [8205.238]) / [8205.238] Add this to user definable Math

    Be Sure to Log Desired Lambda and your External wideband

    This Works For Me, try it for yourself and let me know
    ...
  22. Replies
    1
    Views
    798

    i can help with that if you send me your file.

    i can help with that if you send me your file.
  23. i even sent you a video to show you what was...

    i even sent you a video to show you what was doing..... it was not popping up when you click on the segment. The Problem is and was the software. The Main Window of the vcm editor will not...
  24. Here is a file for example 117195 2009 Taho. As...

    Here is a file for example 117195 2009 Taho. As Stated these parameters seem to be missing in all GEN4 Applications, This function is missing in gen2 and gen 3 as well
  25. also to remove the patch you have to write entire...

    also to remove the patch you have to write entire in vcm editor. if you only write calibration it will not remove the patch. Also, keep in mind you need to keep your laptop charged and vehicle...
Results 1 to 25 of 44
Page 1 of 2 1 2