Search:

Type: Posts; User: legerwn

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Appreciate everyone's input, Thanks Neal

    Appreciate everyone's input,

    Thanks Neal
  2. Appreciate your guidance Joe, Thanks Neal

    Appreciate your guidance Joe,

    Thanks Neal
  3. Thanks for your reply, He's been pretty easy on...

    Thanks for your reply, He's been pretty easy on it,
    His trans cooler is up front around 12" x 12" x 1.5" with its own fan
    Tires are 32" tall, rear is 3.73, stall is 2600
    Driving down the road...
  4. 4l60e and virtual torque tables, 2008 5.3 with BTR Stg 3

    Do the virtual torque tables have the same affect on the 4l60e as they do on the 6l80 trans?

    Buddy of mine has gone through 2 trans at light to medium throttle openings.

    Trans builder says tune...
  5. Thread: Tip in limit

    by legerwn
    Replies
    1
    Views
    487

    Also interested in this one

    Also interested in this one
  6. this can happen when the ECM determines the crank...

    this can happen when the ECM determines the crank acceleration and deceleration pattern has changed from the learned pattern.

    a crank relearn can usually fix it if this is what is happening.
    ...
  7. Replies
    46
    Views
    11,003

    07GTS, does your method work with VVT cams?

    07GTS, does your method work with VVT cams?
  8. need a little help, gen IV proportional rpm error question

    2008 Hummer H2 with L92

    I may have amnesia but need to verify,

    I made some changes to my tune many times playing with the idle and for some reason I remember the proportional rpm error being...
  9. I agree, the butt dyno says 5th with higher RPMs...

    I agree, the butt dyno says 5th with higher RPMs yields less down shifts on gradual grades while cruising on the interstate while 6th is very lazy and down shifting regularly. With the cam I have I...
  10. All around best performance,

    All around best performance,
  11. Whats the best cruise scenario, throttle - RPM - timing

    2008 Hummer H2 (square block)
    L92, 6.2L, GPI LLT 2 cam (2250 rpm and up)
    2600 Circle D, 6L80 Trans
    Thermal Barrier on Piston crown
    DFL-1 coating on piston skirts
    LT Headers with full 3" duals,...
  12. Thanks for the explanation charcoal, I understand...

    Thanks for the explanation charcoal, I understand your point
  13. charcole, what method do you use and what should...

    charcole, what method do you use and what should I be concerned with doing it this way,

    appreciate your input
  14. I should have included that I made both tables...

    I should have included that I made both tables the same then tuned to the fuel I normally use (low grade).
  15. 5FDP, I may not have explained it correctly, I...

    5FDP, I may not have explained it correctly, I understood it to be as you explained it, 1.00 as high table biased and 0.00 as low table biased.
  16. Allowing ECM to manage spark timing, thoughts

    after working on the spark timing tables and getting them where I thought it was close I added 5* to the high table and removed 5* from the low table then allowed the ECM to start tuning the timing...
  17. Replies
    4
    Views
    3,485

    Have you tried to disconnect the shifting cable...

    Have you tried to disconnect the shifting cable and make sure its going to 1st gear by hand at the trans.

    If shifted to second gear it will take off in second gear.
  18. Replies
    3
    Views
    1,462

    They answered my questions pretty quick during...

    They answered my questions pretty quick during normal business hours
  19. Replies
    1
    Views
    743

    Gear selection during VE Table logging

    I've seen it said that when trying to fill as many cells as possible in the VE table it is ok to use a lower trans gear to get to the higher cells (higher rpm).

    It would seem to me that this...
  20. Replies
    132
    Views
    141,614

    OK, mine is discoverable but I cannot find the...

    OK, mine is discoverable but I cannot find the PIN for the adapter,

    where would I find the PIN for the Bluethooth adapter

    Thanks Neal

    Solved; This turned out to be a windows 10 issue, for...
  21. Replies
    288
    Views
    307,155

    sorry not sure what you mean by mapping for the...

    sorry not sure what you mean by mapping for the 4l60e

    Neal
  22. Replies
    288
    Views
    307,155

    4L60e

    4L60e
  23. Replies
    288
    Views
    307,155

    Being new to the tuning world I've been tuning my...

    Being new to the tuning world I've been tuning my trans for a few days now, I was working on the TCC lockup timing as it would stack the 4th and TCC lockup at around 40 mph then unlock instantly. Was...
  24. Replies
    12
    Views
    5,642

    Yes Sir I do understand the guidance, I...

    Yes Sir I do understand the guidance,

    I should have listed that I am not using a wideband at this time. I do currently have and use an Innovate LM1 to tune my vette, BBC 496 solid roller, around...
  25. Replies
    12
    Views
    5,642

    CSSOB I've watched your tech videos multiple...

    CSSOB I've watched your tech videos multiple times, thanks for putting those together they are a great help for us new guys.

    So are you saying to still shut off the trims while tuning the MAF...
Results 1 to 25 of 33
Page 1 of 2 1 2