Search:

Type: Posts; User: 2therock

Page 1 of 15 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,339

    Hi, Did you ever fix this? I see you got no help....

    Hi, Did you ever fix this? I see you got no help. I need to know if you got it done and what it was? Thanks
  2. Thanks, I will finally get around to doing this...

    Thanks, I will finally get around to doing this this weekend. I sure would like to hear opinions on my scan however.
  3. P0741 TCC Circuit Performance or stuck Open. Tune...

    P0741 TCC Circuit Performance or stuck Open. Tune attached but did you see the scan?
  4. Bump!!!!

    Bump!!!!
  5. Replies
    14
    Views
    2,840

    I tried the 40mph thing and it didn't work, sorry...

    I tried the 40mph thing and it didn't work, sorry for not updating, any of the versions I use are the same.

    HPT support informed me Mopar has the MDS locked down and a dealership tech and/or HPT...
  6. That's good news thanks. Thanks both of you.

    That's good news thanks. Thanks both of you.
  7. Replies
    6
    Views
    482

    I don't have theMPVI2, cannot make myself...

    I don't have theMPVI2, cannot make myself experiment with my Pro it on my car.

    There are lesser expensive ELM327 units on the market, and bogus counterfeit interfaces out there. The ODBLink MX...
  8. Dyno Tune & Sport Mode? 2013 Charger R/T. Compatability? Conflict? Risk?

    I had my 2013 Charger R/T Plus dyno tuned a couple years ago using my credits via HPT.
    I recently enabled Sport Mode and there is definitely a difference in how they run with Sport Mode being more...
  9. Replies
    6
    Views
    482

    Also look at AlfaODB

    Also look at AlfaODB
  10. BCM editing has been surfacing for a while and...

    BCM editing has been surfacing for a while and the one I use needs an ELM327 Compatible interface. It would be nice if one who had HPT didn't need to purchase another interface.

    I imagine or dream...
  11. Are the MPVI and/or MPVI2 Interfaces ELM327 Compatible

    Are the Interfaces ELM327 Compatible? Just curious. Thanks
  12. I'm not an expert but from what little I have...

    I'm not an expert but from what little I have seen working with shift points, not making changes is the problem.
    I'm betting the higher stall converter needs to be accounted for.
  13. Replies
    0
    Views
    313

    Layout Repository Needed

    Can we get a layout repository?
  14. Can I get An Opinion On MY TCC Slip Scan?

    Bumping this up? Updated.

    Russ if you are reading, earlier you said to find out and I took her in and got a suggested service (it was time mileage wise) and they stopped but they are back now and...
  15. Replies
    1
    Views
    479

    I guess its looking for some information not...

    I guess its looking for some information not available because of the disconnect.
    So much simpler to leave the harness alone and disable it in the tune.
  16. I hope you are correct. Some how with all the...

    I hope you are correct. Some how with all the different parameters involved in both the ecm and pcm just for shift points, who knows.
    We are looking into it on another forum and the vehicle owner...
  17. Bump?

    Bump?
  18. 2015 R/T - Gear Ratio Change - What Needs To Be Re-Calibrated? 3.06 to 3.92.

    A 2015 R/T - Just had a Gear Ratio Change from 3.06 to 3.92 - What Needs To Be Re-Calibrated?

    What happens if nothing it changed?

    Thanks
  19. Replies
    30
    Views
    14,512

    They will not respond on it. Its written like...

    They will not respond on it. Its written like crap. You do the EGS init and it just sits there. You wonder why there is no save or write, or continue............... ticks me off.
  20. Replies
    23
    Views
    5,941

    PM Sent.

    PM Sent.
  21. Replies
    23
    Views
    5,941

    I'll check my paper work and get back. Do you...

    I'll check my paper work and get back. Do you have HPT and credits already.
  22. Replies
    23
    Views
    5,941

    It didn't cost me near that much.

    It didn't cost me near that much.
  23. I'll let it be known here how she went. most...

    I'll let it be known here how she went. most likely this weekend.
  24. Thank You, I need it. I have a 2.75 MPH...

    Thank You, I need it. I have a 2.75 MPH difference I need to get rid of.

    After the EGS Init do you back out and the close the program before keying off for 10 seconds, or just.........?
  25. Good luck with it once you find it. As you can...

    Good luck with it once you find it. As you can see I got no answer to my post before yours.

    After following instructions and it kind of leaves one hanging there telling you to do the EGS Init....
Results 1 to 25 of 360
Page 1 of 15 1 2 3 4