Search:

Type: Posts; User: jasonz28camaro

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. I’ve found areas in my truck OS that uses trans...

    I’ve found areas in my truck OS that uses trans fluid temp as the oil temp reading. Not sure if it’s this same situation for the zero pedal tq though.
  2. Check out this video if it’s a swap. Go to 6:44...

    Check out this video if it’s a swap. Go to 6:44 and check this out on your harness. Different pin outs for different years. Might not be your issue but worth looking into. He’s got lots of good...
  3. Replies
    13
    Views
    2,668

    I do appreciate the help. Thank you. Now on...

    I do appreciate the help. Thank you.

    Now on to my next issue. One of those mysterious timing pulls at WOT in 6 and 7th gear only. It’s in the log above, same tune too. Need to probably start a...
  4. Replies
    13
    Views
    2,668

    I did the change you suggested at idle only and...

    I did the change you suggested at idle only and it got right around 73psi. I did not do a WOT pull on it though. I put it back to stock and altered table 18102 (min voltage) to reflect a ZL1 and my...
  5. Replies
    13
    Views
    2,668

    I did not know it was a thing to tune the module...

    I did not know it was a thing to tune the module itself, I figured there was enough fuel-related stuff on the ECM side of things. I did some searches and came back with certain OS do not allow you to...
  6. Replies
    13
    Views
    2,668

    Physically its present but I guess not able to...

    Physically its present but I guess not able to read with this OS.

    I'll up that to 500 kpa and see what it does, give me about an hour.
  7. Replies
    13
    Views
    2,668

    Is there a special way to do it? All I see is the...

    Is there a special way to do it? All I see is the engine and trans when I go to read.
  8. Replies
    13
    Views
    2,668

    Yes

    Yes
  9. Replies
    13
    Views
    2,668

    ZL1 fuel pump tuning needs

    Hi,

    I've noticed my low side fuel pressures being in the low 40s at WOT with my setup. I've got mild boltons with e85 on my 68 camaro with a 2018 truck OS. I'm maybe around 450whp ish and I do not...
  10. Replies
    4
    Views
    1,437

    The sensor wire was unpinned at the ECM...

    The sensor wire was unpinned at the ECM connector. No voltage was at the sensor so it was traced back to the ECM and it was not pinned in all the way. Common from factory from time to time with any...
  11. Replies
    18
    Views
    4,658

    I went with the trial and error route that you...

    I went with the trial and error route that you suggested. I started over form scratch and I read more on this and came across a post saying to uncheck the box that links the TQ tables and tackle if...
  12. Replies
    18
    Views
    4,658

    Thanks for taking the time with this. I?m out of...

    Thanks for taking the time with this. I?m out of town for work for the next month but I?ll jump right back on this when I get back and let you know how it goes.
  13. Replies
    18
    Views
    4,658

    Thanks for the detailed description. This is more...

    Thanks for the detailed description. This is more or less what I had thought you did, I tried to mimic it and my numbers did not come out exactly like yours, I think I took out 5-10% in the same...
  14. Replies
    18
    Views
    4,658

    Here's the current tune with the tq changes...

    Here's the current tune with the tq changes TriPinTaZ made and the TB max area set to 5136. I've also included an idle log, cold start to around 17X degrees.

    108005

    108006
  15. Replies
    18
    Views
    4,658

    Thanks for the reply. I get how the torque works,...

    Thanks for the reply. I get how the torque works, I?ve just never adjusted it and was curious to see how exactly you did it.

    I?ll try to get some logs up and have y?all check them out soon.
  16. Replies
    18
    Views
    4,658

    So I still cant tell exactly what you did. When...

    So I still cant tell exactly what you did. When you compare it shows you changed the coefficient tables but is that just showing the changes to the VTT trickled down to the coefficients? I guess I'm...
  17. Replies
    18
    Views
    4,658

    Cool, I see it now. Did you subtract in the area...

    Cool, I see it now. Did you subtract in the area by a percentage or take an actual torque number out? I see you only did the e85, is it good practice to do pump gas areas in the VVT too now or wait...
  18. Replies
    2
    Views
    1,244

    https://forum.hptuners.com/showthread.php?90442-LT...

    https://forum.hptuners.com/showthread.php?90442-LT5-TB-upgrade-tuning-issues

    Check out my tune file here. Go to trans diagnostics and look at the DTCs that we?re turned off. This should get you...
  19. Replies
    18
    Views
    4,658

    Thanks for checking it out. It did seem to help,...

    Thanks for checking it out. It did seem to help, I'm at 3-5 degrees now. What did you change?

    I got a recommendation from a facebook group that said to start over and just use my stock VVE table...
  20. Replies
    18
    Views
    4,658

    LT5 TB upgrade tuning issues

    I added a LT5 TB and I'm getting negative timing at idle. I did a search and some say to get the MAF and MAP side of things in order first before attempting anything else and I ran into another...
  21. 107706 Heres the file you needed if you havent...

    107706

    Heres the file you needed if you havent got it yet.
  22. Replies
    4
    Views
    1,788

    I like that reply. Reminds me of a Dr. Seuss book...

    I like that reply. Reminds me of a Dr. Seuss book lol.

    I got a 10 speed, I love it, also love the 8 speeds, not so much feeling the 6speed autos though.

    So I?m familiar with keeping the...
  23. I’m interested if anyone has done it on a truck...

    I’m interested if anyone has done it on a truck too? I have a swap car with 2018 Tahoe OS with a 10 speed. At the moment I cannot even shift at high rpms while doing tapshift, I may be able to adjust...
  24. Have you searched camaro6 before? It?s not a...

    Have you searched camaro6 before? It?s not a truck OS so I?m not sure how much applies to your application.

    https://www.camaro6.com/forums/showthread.php?p=10640039
  25. Replies
    2
    Views
    1,052

    What fan/s are you using?

    What fan/s are you using?
Results 1 to 25 of 59
Page 1 of 3 1 2 3