Search:

Type: Posts; User: blindsquirrel

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    39
    Views
    810

    No, that table - the Shift TM (Trans > Torque...

    No, that table - the Shift TM (Trans > Torque Management > Torque Reduction > Pattern X/Y/Z) - is the % of torque reduction it wants, and only during the shift. It reduces engine torque by pulling...
  2. Replies
    39
    Views
    810

    Stock tune:...

    Stock tune:
    https://forum.hptuners.com/attachment.php?attachmentid=89651&d=1557558823

    Reduced shift timing, increased pressures, increased Shift TM:...
  3. Replies
    39
    Views
    810

    That table is the % of engine torque to reduce...

    That table is the % of engine torque to reduce by, which it achieves by reducing spark timing. Bigger numbers = less timing = less torque = less slip during the shift.

    I am not looking to bang...
  4. Replies
    39
    Views
    810

    I have my shift timing at .250s across the board,...

    I have my shift timing at .250s across the board, and this is my shift TM table...

    97535

    Still a work in progress, under certain conditions like lifting the throttle just before a shift it...
  5. Replies
    39
    Views
    810

    Raising shift pressures is good (less slip),...

    Raising shift pressures is good (less slip), reducing the shift timing tables is good (even less slip), reducing Shift TM (lots more slip) in a 400HP, ~5000lb AWD SUV scares me a little.
  6. Replies
    39
    Views
    810

    You can attach files here. Find the 'Go Advanced'...

    You can attach files here. Find the 'Go Advanced' button below the quick reply box, that takes you to a full editor with a 'Manage Attachments' feature a bit down the page.
  7. Replies
    39
    Views
    810

    Owner's manual describes it, if you have one. I...

    Owner's manual describes it, if you have one. I can copy/paste the relevant section if you don't.

    In short, the only way to kill it 100% is to pull the ABS fuse, even with TC & Stabilitrak...
  8. Replies
    39
    Views
    810

    It will work either way - in two steps, or a...

    It will work either way - in two steps, or a single long press. And it's just a button, you can go push it and see what happens yourself. Nothing will explode.
  9. Replies
    39
    Views
    810

    Press the button to turn off TC, press & hold for...

    Press the button to turn off TC, press & hold for ~10 seconds to turn off Stabilitrak. Both reset back to 'on' after every key cycle.
  10. Replies
    16
    Views
    1,463

    Sticky: I get the issue on Win7 x86 (flashing/logging...

    I get the issue on Win7 x86 (flashing/logging laptop), but not on the Win7 X64 (editing desktop), if that helps.
  11. Replies
    16
    Views
    1,463

    Sticky: Not really an option for those of us still on...

    Not really an option for those of us still on outdated/unsupported Win7 machines. Guess I will just live with it until future releases just don't work at all.
  12. https://www.google.com/search?tbs=li:1&q=site:foru...

    https://www.google.com/search?tbs=li:1&q=site:forum.hptuners.com+e78+fans

    Look through those, I don't know if there's a solution in there.
  13. Replies
    16
    Views
    1,463

    Sticky: https://forum.hptuners.com/attachment.php?attachme...

    https://forum.hptuners.com/attachment.php?attachmentid=97349&d=1584155413

    Close Editor, window closes, then this pops up. This happens on one machine but not another.
  14. Replies
    16
    Views
    1,463

    Sticky: Installing this latest 4.3.6.0 stealth-deleted...

    Installing this latest 4.3.6.0 stealth-deleted the beta I had installed. Would be nice if it'd ask or at least notify about that first.
  15. Replies
    4
    Views
    167

    I think it's because on Gen3s the TAC is a...

    I think it's because on Gen3s the TAC is a separate external module, and the 'tune' in the TAC isn't accessible, and the PCM tune has to be compatible with the non-accessible tune in the TAC. If you...
  16. Replies
    7
    Views
    269

    If you post the tune, other people can take a...

    If you post the tune, other people can take a look and give you an answer without having to ask a hundred questions back and forth - 'did you set this to X? what about turning off Y?' etc.
  17. DTC P0010: Camshaft Position (CMP) Actuator...

    DTC P0010: Camshaft Position (CMP) Actuator Solenoid Control Circuit

    If you removed the VVT parts, why would you not just kill that code (and any other related codes)? You don't need it/them. The...
  18. Replies
    3
    Views
    115

    The 3.4L uses a P04, is the Cavalier 2.2 P11...

    The 3.4L uses a P04, is the Cavalier 2.2 P11 likely to be the same/similar enough? If it is, that one has VATS Enable/Disable controls.
  19. Replies
    3
    Views
    115

    I can only find a sample file for that with a...

    I can only find a sample file for that with a 3.4L, but there the only options are VATS: PWM or Serial. No option for Disable or None.
  20. Replies
    8
    Views
    249

    CAN devices won't appear in the scanner until...

    CAN devices won't appear in the scanner until they're connected and communicating.
  21. Replies
    4
    Views
    155

    Well don't know what to tell you other than 'post...

    Well don't know what to tell you other than 'post your file' but that's so last year...

    I had the issue trying to turn off P1482, changes would revert every single time until I closed all the...
  22. Replies
    4
    Views
    155

    Close all open subwindows in the Editor, then...

    Close all open subwindows in the Editor, then save as a new filename. Close & reopen to verify it stuck.

    There are a few codes that are really weird that way.
  23. Replies
    9
    Views
    253

    Yeah, looks like that SN should be fine with the...

    Yeah, looks like that SN should be fine with the Vette OS.

    https://www.gmpartsdirect.com/auto-parts/2012/chevrolet/corvette/base-trim/6-2l-v8-gas-engine/electrical-cat/powertrain-control-scat
    ...
  24. Replies
    9
    Views
    253

    Just out of curiosity, what's the service number...

    Just out of curiosity, what's the service number on your current ECM?
  25. Replies
    9
    Views
    253

    If it's a major pain to find someone able to...

    If it's a major pain to find someone able to reprogram what you already have it might be easier to buy a replacement, lots of places offer 'programmed to your VIN' bench flashing with used ECMs. Just...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4