Search:

Type: Posts; User: mbray01

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    254

    you need a special math, eq ratio error, and eq...

    you need a special math, eq ratio error, and eq ratio error bank seperated
  2. Replies
    6
    Views
    1,046

    yep, write entire with updated os

    yep, write entire with updated os
  3. i used to have a mount, that had a flat plate at...

    i used to have a mount, that had a flat plate at the bottom that slid between the passenger seat and the center console. It worked good, was just cumbersome and time consuming to mount the laptop to...
  4. YOU CAN EMAIL ME @ rustyknucklegarage@yahoo.com...

    YOU CAN EMAIL ME @
    rustyknucklegarage@yahoo.com

    be sure to tell me what version your using, so if I make changes it doesnt affect what version your on
  5. The first thing i notice in log, is the fuel you...

    The first thing i notice in log, is the fuel you are commanding vs what you are achieving. I didnt look at the tune, but i am going to assume you have a ton of fuel in the pe table, to compensate for...
  6. i see your logging fuel system status, which...

    i see your logging fuel system status, which remains closed loop. I assumed fuel source, thats what should be logged, as it will determine if it is actually going into power enrichment, or being...
  7. If you use the cable professionally, i would...

    If you use the cable professionally, i would recommend keeping the old cable, with older software, and if you need to have the new software for newer vehicles, i would purchase the newer cable and...
  8. I agree with the guys here, you need to be...

    I agree with the guys here, you need to be logging inj duty cycle. Inj pulsewidth etc. It definately is out of injector. Its not commanding op, that i can see, its staying in closed loop, granted its...
  9. Replies
    9
    Views
    351

    Airaid even makes a drop in filter and high flow...

    Airaid even makes a drop in filter and high flow elbow that uses the factory air box, for about $200. This honestly is a really good setup
  10. Replies
    9
    Views
    351

    Volant, corsa, airaid(with a sealed box), s&b,...

    Volant, corsa, airaid(with a sealed box), s&b, afe(with sealed box). Basically anything with the sealed box, if it has a piece of sheet metal and a rinky hood seal, it is worthless.

    Personally im...
  11. Replies
    9
    Views
    351

    My best advise is to throw that k&n hot air...

    My best advise is to throw that k&n hot air filter into the garbage, and get a true cold air intake. As for changes, most of the systems designed for trucks use the same size tube for the maf, so...
  12. Replies
    8
    Views
    392

    From the stock tune start here, it will get it...

    From the stock tune start here, it will get it running just enough to drive to the speed shop without much issue

    under airflow-dynamic set high rpm disable to 200, and re-enable to 100
    under...
  13. Replies
    4
    Views
    174

    The issue they are describing, its remedied by...

    The issue they are describing, its remedied by turning the scanner off completely and restarting it. If that doesnt fix it, contact support, they can help with more pressing issues
  14. Replies
    22
    Views
    814

    the problem is that you were given no data. that...

    the problem is that you were given no data. that isnt what we look for with data. there are voltage offsets, pressure offsets, and calculations for when the injector is ramping open and closed. the...
  15. Replies
    2
    Views
    143

    If it is ecm controlled, yes, if it has an...

    If it is ecm controlled, yes, if it has an aftermarket module controlling it, no
  16. No secrets to hide. If your ecm has to relearn...

    No secrets to hide. If your ecm has to relearn before it acts right, then something is not properly calibrated. Unfortunately im not going to type out a long how too on tuning, as that has been done...
  17. Replies
    7
    Views
    270

    Ive never come across one that didnt work, when...

    Ive never come across one that didnt work, when properly set up. Do you have maf failed correctly? Are you making changes, then smoothing the table, if you are, its likely smoothing your changes...
  18. Replies
    33
    Views
    2,398

    again as stated, knock sensors are very sensitive.

    again as stated, knock sensors are very sensitive.
  19. Replies
    3
    Views
    158

    if its sweeping back and forth while full, its...

    if its sweeping back and forth while full, its likely a bad connection. the connections at the passenger foot well are notorious for problems
  20. Replies
    3
    Views
    216

    there are tons and tons of write ups about adding...

    there are tons and tons of write ups about adding proper injector data, getting a base file working, and how to get idle working enough to get the tuning process started. do some searches, there is a...
  21. Replies
    8
    Views
    249

    If you have can low and can high connected, and...

    If you have can low and can high connected, and still receiving nothing, i would contact support directly. Sounds like there may be some comm mismatch issues
  22. Replies
    8
    Views
    249

    What are you trying to log on can? Maybe if you...

    What are you trying to log on can? Maybe if you tell us what your trying to accomplish, we can better help
  23. Hes not asking how to power it up, hes asking how...

    Hes not asking how to power it up, hes asking how to make the ecm think the engine is running when its not attached to an engine. To do this essentially at a minimum you would need a 24x signal...
  24. Replies
    6
    Views
    547

    Dave steck????

    Dave steck????
  25. Replies
    6
    Views
    408

    Are you looking for an already built tune, or...

    Are you looking for an already built tune, or just the base file to tune from
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4