yeah I have some of those. I dont think it will be correct
Type: Posts; User: konabluekiller
yeah I have some of those. I dont think it will be correct
ISO a Whipple base for a Raptor 6.2. Customer truck here and had lots of issues. Tune was locked and I started over from scratch and used a tune I'd put together for a Roush supercharged Raptor......
I understand that much. Could you supply some guidance or base file help? I'm not above paying for learning.
We just finished up a car with D1X Procharger, 12 psi, Fore Triple Pump and other misc additions. Car runs, drives, dynos, cold starts and everything great.
The issue I'm having is during a WOT...
Thanks! Searched on Google because I had high idle on a customer vehicle. The clean throttle switch fixed it...
That makes throttle close. But yes on the whipple tune it works
ISSUE: pulling timing during a pull and torque source says (torque based decel)
2019 F150, On3 turbo, dw95s, e85, 4wd
When rolling into the throttle everything seems fine, but when leaving from a...
Yeah I wonder if there's a base cal out there that doesn't have it locked down. I have plenty of mustang ones.
2015 f150, 2.9 Whipple Stage 1
Truck came in with unknown tuners file. Truck wouldn't read but a few parameters on the scanner.
We flashed our base file to start with, with write entire. Truck...
Apparently the torque in the tables in that area needed to be lowered, and the 2 tables for the throttle body model needed some adjusting to make it more linear.
Made a histogram logging ETC error to change predicted and effective throttle area...
Made another one for throttle error vs load and rpm....
Made the appropriate changes to the torque and...
I will take a new one tomorrow...
That log was taken before I had a chance to change channels and log again. Has the 132mm throttle. Gen 5 3.0 blower.
log and tune
115817
115818
Yes. When I get where I can post tune and log I will. Currently posting from phone.
Throttle surge issue
Gen2 5.0/6r80 swapped into a Fox Mustang with a Gen5 Whipple 3.0. Did a base calibration on the dyno and got it running, idling, and driving on dyno fine, wot fine (700 whp at...
I also need gen5 3.0 file. Tuning a swapped Foxbody and doing it from scratch. I have lots of older whipple cals but this one is fighting me.
Needing a base cal that will work for a Control Pack. I have lots of whipple base cals but due to PATS they won't spin the engine over with the key. Even with the PATS switch disabled in the system...
gen 2 trucks have an oil pressure rev limit at 3000 rpm. That parameter was hidden. HPtuners support now added that to the new beta to raise the rev limit per oil pressure for swapped cars without...
Engine speed limit issue.
Gen 2 coyote truck engine, harness, and pcm swapped into a Gen2 Lightning chassis.. Has gen 4 2.9 Whipple and 1050x Injectors. It is the competition kit with the Whipple...
yes... that was verified. It will turn over on other tunes but not a whipple cal
No crank condition issue
Gen2 F150 Coyote with Whipple
Swapped into gen2 lightning with MARS harness and Pats delete pcm.
Stock file will start truck (of course runs like crap). I took a 2017...
Can you post the base whipple truck cal? I am having same issue with a customer who swapped a gen2 truck motor with whipple into a lightning...
I was hitting a limit and raised some stuff in the tune to make it work with the 3.65 pulley. Then we started adding nitrous and each time we would up the shot we would run into another limit closing...
I have a couple base Cals for a roush mustang but they are all automatic cals. Needing one for a manual Gen1 car to base a new tune off of. Thanks