If you can't change that background table set, you might want to put that etc max setting back to stock. I've seen in rare instances where having the 2 so different would actually cause some idle...
Type: Posts; User: GHuggins
If you can't change that background table set, you might want to put that etc max setting back to stock. I've seen in rare instances where having the 2 so different would actually cause some idle...
It can be. It's called throttle mode or something like that. I would dump quite a hefty dose of marvel in it if correcting the injector data and reworking your VE and MAF tables don't solve it. Might...
Well, I mean if it didn't do it before and nothing was changed with the build, then it would have to be a mechanical associated item. I guess it could be idling at a different airflow requirement now...
Are you sure the injectors and rails are clean? Not to mention the lines to them? This could simply be a supply issue, but usually you see that with rpms on top of off idle. You could even have...
So are we to understand that nothing on the engine has recently been changed and this issue just started out of the blue?
Well, I said that and then found out Will has shut things down for a few months until he can get caught up with several other things. I think he even took down the site to be able to do so. I know...
This is a channel config you can use since it's boosted. If you need to add anything, you can.
To load - download - right click - show in folder - copy - open scanner - open recent channel config...
You might just want to find and compare it to a stock file. VE and torque models are the only other ones I glanced at. Stock comparison will show you what was changed and you can look at it to see if...
Got your PM.
This is what I'm referring to for the ethanol timing. A trick for dialing in ethanol timing is to "copy with axis" the ethanol timing table then "paste special add" to the 93 octane...
Voltage and position look good in this log as long as tps 1 and 2 are also changing correctly, which aren't in the log. What code is being set to induce the REP?
You need a log, but just looking at the cal I think it's good you have a manual considering the things that were adjusted incorrectly and what wasn't dialed in at all. Otherwise you could probably...
The blade is most likely hitting something causing it to not open for it to just stick around 30%. I would open and close it with the key on engine off via scanner controls to confirm then start...
Seems like nobody has the 19 :D
I've got some 19 z06's, but they were already modified when I started on them so I don't even have stock files for them.
Would an 18 manual work?
I know the pump is super pricey, but you might want to look into that too. You can wind up starving the rails with too small of a pump with the bigger injectors.
HPT does this with a lot of the tables. I don't understand why, but they'll only put in half of what you need, so you think you have everything only to find yourself going in circles spinning down...
Manifold volume if you have it you can change. Throttle max you need to leave stock.
I'm not so sure the VE is his actual problem. When I look at the VE table that his is actually using and look at the data then yes his VE table is 2 to 4 g/s off in a lot of places, but is that...
If you have the obd2 Aem then unplug the d d and plug the other 2 in like normal. If you don't then use the pro link like you're talking about.
I've never been able to log with the gauges plugged in. They always interfere with the scanner being able to log correctly. I just use my cell with a gps app to get a rough speedo reading while I'm...
Sure you're not referring to DFCO? Decel fuel cut? Normal for the wideband to read full lean as it's just pumping air through the motor.
You need the rear O2s. What happens when you delete them without setting the background tables up accordingly is during decel it dumps fuel. It dumps fuel to "protect" the cats because it doesn't...
You can't delete the rear O2's. Put them back then check your plugs as advised. Without the rear O2's you're guaranteed to run 10% lean ;)
Do you not have a valley port?
Normally, it's valley port to catch can, then catch can to behind TB in the SC. Then valve cover to intake pipe post MAF in the airflow measuring process. I...
I can't look at the log, but no pedal and poor idle is usually rep
I think the tune file is what's missing - not the log. Just says it's translating it when I try to open it. Never seen that before.
It shouldn't be pulling that much vacuum on the can. Post some...