Awesome!!! Could you please share the details of how it can be done?
Type: Posts; User: SVTuner
Awesome!!! Could you please share the details of how it can be done?
Thank you very much :)
I'm sure this has been covered but I'm having trouble finding the info. When you have removed the MAF and in VCM Scanner you want to create a histogram to map spark advance, in the editor it is...
So I've got a single turbo setup with a narrow band in the RHS bank and a narrow band in the dump pipe. Been trying to get it to work in closed loop but one side just thinks it is rich and tries to...
Guys thanks so much for the pointers. I downloaded the injector data from HERE. Then I followed THIS thread, doubled the Stoich and halved the value of the new injector flow rates. The engine...
Wasn't aware of that, thanks. I'll do some digging.
I've downloaded the data and checking it out now.
I'm not running a MAF so didn't see the point of changing anything with dynamic air or MAF frequency since the ECM knows it isn't there. I'm open...
Hi all,
Have just put in a set of Deatschwerks 65lb injectors, were previously on a 2300SC LS3 and I'm fitting them to a Turbo LSA.
https://www.summitracing.com/parts/dwk-16u0000658
Engine...
Never mind, installed version 4.4.4 and it works now.
Sorry if this has been covered before but I downloaded a file from the repository and I get this message. Most likely it's due to my version of VCM Editor being a lot newer but is there any other...
I'm 99% certain the license is not tied to the VIN so no, you won't get away with writing your old tune to your new ECM without purchasing more credits. There are plenty of threads here that...
That was it, thank you so much!
Torque Management>RPMvsGear made all values 8192.
Hi All,
I'm absolutely stumped what is causing this. I've just put a Turbo on my LS, wrote the 2 Bar OS and built the VE Tables. When I put it under moderate load the ignition timing drops right...
Anyone have a recommendation to setup a VE Table for the 2 Bar OS for E38 ECM? When you apply this patch the new VE Tables are filled with zeros. I was thinking of copying the VVE Table and then...
Checked and yes, it is there :)
Thanks 5FDP, I'll have a play with the software and see how it goes. According to the following thread, there is a custom OS for E38's for 2.5 Bar so I'll use that. Refreshing to see they are now...
Hi Everyone,
In the final stages of putting on a single turbo so I've got a couple of questions regarding configuration for boost and O2 Sensors.
In regards to boost, I've done an E40 ECM in the...
Thanks for that vital piece of information. Managed to find just about everything else except that.
So how does the transmission know it is in sport/manual mode? Is this circuit not powered when in drive (D) and when the 8.25k ohm part of the circuit is energised that enables manual mode? Is the...
Really, the TCM is paired to the license? I can understand the ECM but the TCM as well? So if you have a module failure and it has to be replaced it has to be re-licensed?
I'm undertaking a project where I need to flash in a number of trans and engine OS's until I find a compatible match as the vehicle was not originally equipped with a T43. From what I understand,...
Hi Everyone,
I've just replaced my Transmission Control Module (T42) and now when I try and connect I get Detect Protocol Failed error. The original module when I hook it back up works fine. I get...
Could you relocate the temp sensor to the downstream side outlet of the intercooler? You would avoid a lot of radiant heat having it there.
Hi Paz,
My build is a bit on the different side of things. I'm using the Engine and 6l90E from the VF GTS into a VZ Crewman. I'm going to be using the VZ E38 (originally L76) and a TBM 4L to 6L...
Sorry if this has been posted before, did a few searches but couldn't find anything.
I'm in the process of building a single turbo LSA (no supercharger) and I was wondering what do I need to...