Search:

Type: Posts; User: Ditosmotors

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    873

    Flex Fuel Patch on existing tune

    2016 Hellcat Challenger A8

    I dont have the original tune for this vehicle but wanted to do another flex fuel setup. Normally I apply the patch to the stock file but I dont have that. Is it ok to...
  2. Replies
    5
    Views
    2,876

    So I had sent the computer back in to Hp tuners....

    So I had sent the computer back in to Hp tuners. I'm not sure what they did with it but I have it back in the vehicle with the HP tuners bypass installed now. I am still getting the P0600 code. It...
  3. Yeah, I realized that right after I posted. I...

    Yeah, I realized that right after I posted. I just copied the normal table to the MAX TIP table and now its doing what I want. Thank you.
  4. Exhaust Cam Timing Commanding diffrent then tune

    2013 Dodge Challenger RT automatic
    Whipple, 392, hellcat cam

    The problem I am having is with the exhaust cam timing. The only time it will do what is programed in the tune is during WOT. At idle...
  5. Replies
    8
    Views
    2,813

    EGR Monitor with aftermarket VVT cam

    Has anyone out there been able to get the EGR monitor to show complete once an aftermarket cam has been installed in one of the VVT engines (Eagle or Apache)? It seems to me that it needs to see a...
  6. Replies
    5
    Views
    2,876

    I feel confident the connection is good. With the...

    I feel confident the connection is good. With the stock computer I dont have this code. Only with the unlocked computer. I am using a Zautomotive bypass, not the hp tuners bypass. Ive used them...
  7. Replies
    5
    Views
    2,876

    Still can figure out this P0600 code. The one...

    Still can figure out this P0600 code. The one thing I noticed was that the cooling fan turns on no mater what the temp is when you start up the vehicle and it goes to high speed. I'll post up the...
  8. Replies
    5
    Views
    2,876

    2018 Track Hawk P0600

    Anyone run into a P0600 after installing a new unlocked computer in one of these vehicles. This is the first new computer I've installed in a 2018 as I've always just sent in the original computer to...
  9. Replies
    1
    Views
    836

    Got it, right click table and select %

    Got it, right click table and select %
  10. Replies
    1
    Views
    836

    VE table 4% and 400% max

    I noticed that the ve tables have bank one at 0 to 4% max and bank to 0 to 400% max. So on bank one you might have 1.03 and on bank to its 103. I noticed this on the latest full version and the beta...
  11. Hellcat Flex fuel Upstream Goal Voltage Offset

    2016 hellcat manual trans challenger. I believe I got most of my issues worked out but I'm concerned about "Upstream Goal Voltage Offset" I think I have the FAR offset worked out and I'm guessing...
  12. Replies
    2
    Views
    1,065

    Makes sense, when I read my DS tune with Hp it...

    Makes sense, when I read my DS tune with Hp it showed the SRV enabled even though I had it disabled. Thank you.
  13. Replies
    2
    Views
    1,065

    15 jeep srt8 P2008 2016 1004

    Has anyone run into these codes after disabling the SRV? (P2008 P2016 and P1004). Normally when I have disabled the SRV I dont remember getting any codes but this time I did. I ended up just...
  14. Replies
    12
    Views
    5,907

    Sorry I guess this only has the min phi and not...

    Sorry I guess this only has the min phi and not the gain table found on the WK2's.
  15. Replies
    12
    Views
    5,907

    I wonder if adjusting the Min PHI to 1.000 would...

    I wonder if adjusting the Min PHI to 1.000 would help at all. (13554) Airflow>Electric Throttle>Min Phi. I often will set this and the proportional gain table all to 1.00 when I have an unstable...
  16. Replies
    12
    Views
    5,907

    Im not sure how air flow is calculated but I...

    Im not sure how air flow is calculated but I noticed that your map reading is low for WOT conditions. Normally I see that in the upper 90's to low 100's kpa. I would probably try putting in the stock...
  17. where is that max pr table? At last resort...

    where is that max pr table?

    At last resort I'll either try clamping that Max pr to 1.8 when I get a chance to get back on it or I'll go back to a diffrent pulley. I was thinking I was hitting some...
  18. 2014 jeep procharged goes lean above 200KPA

    2014 Jeep F1A, forged internals, mystery cam, 6.1 intake, 90mm tb, long tubes, E85 with triple fore pump kit, ID 1300X.

    When the boost gets to about 14-15 psi this thing goes extremely lean. When...
  19. Replies
    8
    Views
    2,256

    Getting a log of this problem when it occurs will...

    Getting a log of this problem when it occurs will be difficult because it happens rarely. When I use my Autel scan tool to look at mode 6 data, you can see that it will have logged a miss on cylinder...
  20. Replies
    8
    Views
    2,256

    The code is P0308. I believe it only runs rough...

    The code is P0308. I believe it only runs rough at the time the light comes on because the pcm is shutting down the injector on that cylinder.
  21. Replies
    8
    Views
    2,256

    14 Ram 1500 Eforce miss fire code

    2014 Ram 1500 with Eforce supercharger

    About once every few weeks this truck will throw a miss fire code for cylinder 8. It always happens when cruising. When this happens the truck will run...
  22. Replies
    11
    Views
    3,926

    Well, we replaced the camshaft and the cam...

    Well, we replaced the camshaft and the cam sensor/oil pump drive because the gear on both was just about gone. While the head was off we had that rebuilt. We also noticed that two of the primary cats...
  23. Thank you, that table took care of it.

    Thank you, that table took care of it.
  24. I'm still on the latest 3.6 offering. I'll down...

    I'm still on the latest 3.6 offering. I'll down load the 3.7 and get that customer back in here so I can give these ideas a try.
  25. I tried raising a torque limiter I found in the...

    I tried raising a torque limiter I found in the trans side. Torque management>Gear max limit normal. When I change these the check engine light stays on with code P1DF3, U0402 and P1DD2 Torque...
Results 1 to 25 of 47
Page 1 of 2 1 2