Other then the soft shifting. Do you notice any other problems? You made mention of your TCC applying. Are you just stating this to indicate it's working properly?
On your pressure table. Did...
Type: Posts; User: OneSlowGTP
Other then the soft shifting. Do you notice any other problems? You made mention of your TCC applying. Are you just stating this to indicate it's working properly?
On your pressure table. Did...
I see quite a few other people are having similar issues? Has any fix been discovered for this yet?
The tables that you seek are in those BIN files. If your too lazy to download and look yourself, then don't expect me to spend the time to post it for you.
Best site I've found for .BIN files:
http://www.horist.com/hptuner/search.asp?action=exe
-enjoy
A few strange things to note about the car's behavior with the MAF disconnected...
I have 3.69 gears so I hit 4th gear at 35mph.
at 60 my RPM during lockup is rather high.
with the MAF...
I actually had the opposite problem before: My MAF had failed, (which I did not know) and the car wouldn't start. I thought something was really wrong. I cut open my oil filter and poured out the...
Well, I was able to verify that NO the PE table does not make trim adjustments unless the car enters PE mode.
I was hoping to get my trims dialed in for a few reasons. One to see if there was any...
And here are the tables for those interested:
1999 Grand Prix GTP MAF Table:
1.62 2 2.4 2.83 3.27 3.74 4.38 4.9 5.66 6.34 6.9 7.65 8.58 9.61 10.55 11.53 12.81 ...
It doesn't flow any more or less air so much as it reports a different frequency for the amount of air that it DOES flow.
For example:
if you are flowing ~350 g/sec of Air
a 99 GTP MAF would...
uhm, What is your idea here? To transplant A4 values from the GTO into...... a 3800 V6 A4 table?
If you want firmer shifts, just raise your line pressure, add the + / - Force motor current values...
Well that would be interesting because 0 to 35% throttle, +2.3 is commanded.
That would convert a target A/F of 14.7 to 16.9 (lean) and require more fuel to bring it back in check.
(my car...
That's only for "Power Enrichment" though... I'm talking for general driving.
If you have a “perfect” Injector flow rate calibration
And a “perfect” MAF calibration
What would you adjust to make your car run richer or leaner?
I imagine variables such as cam...
Agreed, anytime you add tables, you offset all the data.
However....
Changing the resolution or granularity of the table should allow you to have a wider range without offsetting any of the...
Ahhhh, that makes sense :)
but...
My "General Tab" is blank :-\
I imagine I have no "Fail Frequency" based on that and the fact that I've never gotten a code for high maf freq as I'm...
I was looking for the formula to calculate it without using the MAF. Strictly the VE table.
For example:
with a MAP kPa pressure of 100
and an Engine RPM of 2400
you get a VE value of 74...
If GramsAir is being calculated from the VE table instead of the MAF table, what does the formula look like?
Thanks,
-Andy
MAF range is 1500 - 11500Hz, I reach flow figures over 11500Hz, I'm still not sure what you mean by MAF Fail frequency?
Info about the car below:
1999 Pontiac Grand Prix GTP
Diamond...
I agree, there is defiantly more too it then Injector size and MAF freq. Anyone who doubts this can easily run an experiment to prove it.
simply scale your injector size by 200%
then scale...
Supposedly the table provides transient correction, and checks for MAF failure. If the tables were that far off, wouldn't the PCM think the MAF has failed?
Lets say hypothetically I disconnected...
99 GT VE Table:
34 45 68 82 91 97 93 98 95 99 102 99 107
34 45 68 82 91 97 93 98 95 99 102 99 107
41 46 54 57 60 63 68 91 96 ...
:huh2:
I am a little confused as to how to inturpret and thus tune the VE table for Supercharged V6 engines.
First off MAP pressure is limited to 140kPa however a typical boost values are in the...
I guess your already a step ahead.
Looking forward to it :)
-A
Never heard of such a thing. Have you considered installing the MAF before your Turbo and just upgrading to a 3-BAF MAP sensor. That would probably give you the best results.
If you want to...
I don't know how much bandwidth or storage you guys have, but I was just wondering if there was any space on this site to host pics / video clips...
Sometimes it would be easier to expain a...