Search:

Type: Posts; User: castorjames

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. i have used sykedecutuning $130

    i have used sykedecutuning $130
  2. Yes, it works like that, on my case, it idles at...

    Yes, it works like that, on my case, it idles at around 3000hrtz and goes to 940-950htz at WOT with 80KPA of boost.
    Also fueling follows MAF table modifications nicely..
  3. thank you, this one is the same OS..

    thank you, this one is the same OS..
  4. thankyou

    thankyou
  5. auto

    auto
  6. 2012 grand cherokee 6.4L stock file, any one?

    need a stock file from a 2012 grand cherokee 6.4L
    anyone?
  7. ...

    ...
  8. Replies
    17
    Views
    347

    that would be your low fuel side pressure, need...

    that would be your low fuel side pressure, need to log fuel rail pressure as suggested by proxses
  9. 2019 Silv File

    ...
  10. Replies
    12
    Views
    766

    any updates? kinda having same problem? any help?

    any updates? kinda having same problem? any help?
  11. current tune with ID1300x2 and 2.75 upper...

    current tune with ID1300x2 and 2.75 upper pulley, 92 oct fuel

    Since installed the 2.75 pulley having a problem that looks like FUEL CUT OUT? it cuts fuel when it hits 200+KPA, in this log it cuts...
  12. Replies
    2
    Views
    99

    Yes, if you have enough injector and pump to...

    Yes, if you have enough injector and pump to provide that extra fuel, start richer and work backwards. i prefer wet system
  13. any help? looking to hit the track in couple of...

    any help? looking to hit the track in couple of days and would like to improove it if possible, ill lower shift points and retest cause was shifting at 6800rpm(feels ok), any ideas how to lock tcc at...
  14. went to the track, did 11.9, spins 4 wheels...

    went to the track, did 11.9, spins 4 wheels badly,

    it is shifting at 6850 or so, will lower shift target to give it more room to shift earlier.?? feels good as is tho
    Whyit only locks converter...
  15. Glad to help. Have fun, drive safe

    Glad to help. Have fun, drive safe
  16. Shifts at Wot are good now too. just needed some...

    Shifts at Wot are good now too. just needed some more lead time. still converter only locks on first gear, everything else is good.
  17. worked on the last 3 left columns, and now its...

    worked on the last 3 left columns, and now its good, shifting from neutral to drive/reverse now is smoth,and closed throttle downshifts now are good. thank you
  18. Replies
    3
    Views
    141

    i have same snsor but check your baro/map on the...

    i have same snsor but check your baro/map on the scanner software with key on engine off
  19. 6l80e has the trans range attached to the TCM,...

    6l80e has the trans range attached to the TCM, you need to be careful when reinstalling, you need to remove your trans pan, and remove TCM again and install properly, there is a shaft that moves the...
  20. Replies
    29
    Views
    1,056

    P057B P057C P057D P057E set to NO MIL, NO...

    P057B
    P057C
    P057D
    P057E

    set to NO MIL, NO ERROR REPORTED
  21. Replies
    29
    Views
    1,056

    did you keep brake travel sensor?, delete all...

    did you keep brake travel sensor?, delete all codes related and test again.
  22. not mine

    not mine
  23. Also why it will only apply converter LOCK on...

    Also why it will only apply converter LOCK on first gear?
    i dont like how it feels with the converter locked at low speed,instead i tried to lock at WOT, but looks like only locks in first gear?
  24. you mean PCS table?

    you mean PCS table?
  25. Replies
    29
    Views
    1,056

    IF your car start and idles your harness to the...

    IF your car start and idles your harness to the throttle body must be OK then, double and triple check your wiring from the ECM to your accelerator peddal, check pin positons, check with multimeter...
Results 1 to 25 of 203
Page 1 of 9 1 2 3 4