Search:

Type: Posts; User: Keudn

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,626

    Is this the same cat test that I am getting...

    Is this the same cat test that I am getting during OL? If so why does it only go up to about 1.15 lambda in OL?...
  2. Replies
    2
    Views
    1,626

    Random spike in commanded AFR?

    I was driving around logging today and I got a random huge enleanment in my commanded AFR that seemed to happen only in a certain throttle range. It only happened for under a minute, and for the...
  3. Replies
    4
    Views
    3,471

    Here are my channels, these are for a 2005 with...

    Here are my channels, these are for a 2005 with an L67. Might get you in the right direction. You can discard the EQ error - 1 charts you won't need them.
    111484
    111485
    111486
  4. So I am still having issues with this problem, I...

    So I am still having issues with this problem, I called around to a few local shops as well as ZZP and from what I learned it sounds like it is indeed a cat test running. They thought that the test...
  5. So the issue the rear O2 sensor circuit is open?...

    So the issue the rear O2 sensor circuit is open? Because I do have a rear O2 sensor installed in the car. I realized I wasn't logging the rear O2 bank, and I added the O2 Voltage B1S2 PID and it...
  6. The car is actually a 2005, however the PCM isn't...

    The car is actually a 2005, however the PCM isn't the original since I had a canned tune in the vehicle before, so I'm not sure what year the PCM is from. Is the test happening because of the P0420...
  7. Is there a way to check if the cat test is...

    Is there a way to check if the cat test is running? Even before tuning for E85 I would notice that in OL the fueling would move around from 0.97 to 1.05 lambda. Seems like its probably a set AFR...
  8. Vehicle leaning under light acceleration and small TPS

    Hi guys,

    I am working on tuning my L67 platform vehicle for E85, and I am seeing some enleanment under small (< 20%) TPS values. I've looked all over the fueling tables but I can't seem to find...
  9. Replies
    0
    Views
    667

    Unable to log Manifold Vacuum? (L67)

    Hi guys,

    I am working on tuning my L67 engine for E85, and I would like to set up a table in VCM Scanner to log my % AFR error from my wideband into a Manifold Vacuum table to get my Flow Rate vs....
  10. Flow Rate vs KPA table tuning with new injectors

    Hi guys,
    I recently installed 60# injectors in my L67 3800 and am working on tuning them. I noticed that my current tune had the table flat across the board at 38.4 lb/hr. I referenced the factory...
  11. Replies
    4
    Views
    2,267

    Alright I'll take a look at that stuff in the...

    Alright I'll take a look at that stuff in the tune. Yeah I'm not really sure whats going on, I think I'm gonna take it to a dyno and just see what numbers it is making. I dynoed it last summer so I...
  12. Replies
    4
    Views
    2,267

    Shoulda mentioned that, 91. Yeah I have a...

    Shoulda mentioned that, 91.



    Yeah I have a wideband and tuned the MAF in open loop



    Yep, set them to 0.045"
  13. Replies
    4
    Views
    2,267

    Excessive knock retard on L67

    Hi guys, I am scratching my head at why my L67 car is knocking so damn much and I'm having to pull so much timing. Its not a stock car, and I'll briefly list the mods I've done just for reference.
    ...
  14. I'm trying to tune my 2003 Cobra with my MPVI2...

    I'm trying to tune my 2003 Cobra with my MPVI2 but I can't read the PCM, it tells me to turn the key to the off position for 3 seconds and then back on again, but it just says controller init failed....
  15. Replies
    3
    Views
    5,321

    Sounds good, just wanted to confirm that it...

    Sounds good, just wanted to confirm that it swinging back and forth was normal operation
  16. Replies
    3
    Views
    5,321

    O2 sensor voltage varying wildly

    Hi guys, I have been noticing in my scans that my O2B1 varys wildly from around 50mV to 900mV. It seems to be somewhat periodic, but the frequency at which it fluctuates seems to vary. Is this...
  17. Replies
    7
    Views
    3,366

    For those with the same issue, the solution was...

    For those with the same issue, the solution was to install the BETA version and launch it, it installs separately from the normal branch and has (BETA) after the program name.
  18. Replies
    7
    Views
    3,366

    PIDs disappearing when recording?

    Hi guys,
    I just recently got my MPVI2, and I have been having some trouble with the VCM Scanner. I am trying to tune my 2005 Monte Carlo SS with the 3.8L SC L67 engine. I have added a bunch of PIDs...
  19. Replies
    9
    Views
    6,845

    I deleted KR, connected the MPVI2, repolled and...

    I deleted KR, connected the MPVI2, repolled and then readded KR. Still disappears when I hit record.
  20. Replies
    9
    Views
    6,845

    Just did a repoll, all the channels in the...

    Just did a repoll, all the channels in the screenshot above stayed there. They don't disappear until I hit the record button.
  21. Replies
    9
    Views
    6,845

    Gotcha, I'll have to go plug that back in and...

    Gotcha, I'll have to go plug that back in and check it. As for the more data, this is what data I have it set up to log when its not plugged into the car
    95615

    But, as you can probably see from...
  22. Replies
    9
    Views
    6,845

    Newbie questions about L67 3800 tuning

    Hi guys,
    I have just started dipping my toes into tuning on my 2005 Monte Carlo SS with the 3.8L SC L67 engine. I have been reading and watching videos, and tonight I went and did a scan for...
Results 1 to 22 of 22