have a customer with a 2010 escape 3.0 wanted to see if i could tune it
running the newest version 3.0 downloaded today it wants a pcm type before it will read
any idea what this vehicle is?
Type: Posts; User: scotte
have a customer with a 2010 escape 3.0 wanted to see if i could tune it
running the newest version 3.0 downloaded today it wants a pcm type before it will read
any idea what this vehicle is?
figured i would ask before i spend credits
ok
if you need any volunteers i have access to an 2008 f250 6.4 and i have a vcm2 / ford ids subscription to do a blank path program to recover it if need be
any rough idea on an eta on 6.4l editing support?
i have a few i need to tune
the vehicle in question is a 2008 grand prix with a 3.8l v6 non supercharged vin 2
the main hp tuners site says 97-07 supported however some hp tuners resellers are claiming 97-08 support
the...
got a 05 expedition that i need to tune (customer vehicle)
pulled file and validation failed
updated to latest 2.24 version and it still fails
reflashed pcm to latest ford calibration via...
i think the ipc uses the speed signal off the abs module (via class 2 databus)
i have the 4.2 motor trans and pcm and speedometer from a 04 envoy swapped into a 98 wrangler and i can change the...
wide band. tuning with ltft was 5 years ago
it can overshoot anywhere on the ve table really (2 bar speed density)
injectors are 42#
4.8l with ls9 cam running 11.5 psi from a m112
...
would like a second multiply by percentage on the right click paste menu
maybe either -75% (so as to change it by a quarter of the percentage) or possibly by a custom percentage?
i find...
ok so my question goes
if one were to modify the injector bank select (under engine/fuel/general) so all the cylinders are on bank1 (which is 0 in injector bank select)
and then remove...
im looking for the best e38 os(year model) as a starting point
im building a ly2 4.8 out of a 09 van (i have the 09 van ecm,harness gas pedal etc) also running a t42 with a 4l80e trans with a...
not sure if this would even be the right forum for this but anyway
my newest project is a 01 wrangler with a 4.8l lr4 motor/ 5speed and tsp 224r cam
just got a used radix m112 magnacharger...
i have seen it done before
the method used was set it up as an 8 cylinder and wire the injectors and coils for every other cylinder on the firing order
then disable the injector/coil codes...
wondering if somebody can take a look at my tune and see what mistake(s) i've made to cause this :)
4.8L with tsp 224 cam, and cai in a 01 jeep wranger hooked up to the jeep 5 speed
file is...
02-05 trailblazer i6 (p10 iirc)
Axis change (switch ve tables to map instead of tps)
A certain "other" company has it I won't name any names (slow serial interface) :)
I haven't tried it yet...
i have the same engine (4.2l) in a 98 wrangler and ive been thinking about giving it some boost for a bit now
(was thinking eaton m90 with a custom intake @ 6psi not a powerhouse but cheap and...
first off i assume that when you replaced the "busted" pcm you had the replacement pcm reflashed to the correct vehicle vin/calibration
this requires either a j2534 device or a tech 2
you need...
you could use hptuners to disable vats in the pcm but not the bcm
it would start but the security light would never go off
if like you say you have swapped in a matching pair of...
i'll email the file to anybody that sends me a pm with a request for the file "07 h3 turbontics tune" and their email address
it may take a day to respond (busy schedule,flaky internet,...
th p12 is also the stock ecu on 06 trailblazers
the p12 is boost compatible with a little work( i have the stock turbo tune for an h3 turbo kit w/ a p12 and copying the tables over will make a...
i'm planning on doing it to my jeep (has 03 4.2 swapped in
the only effect a bus change can have on my application is i may have to switch speedometer clusters
i have most of the parts to do...
chances are that if you go to your local dealer and have them reflash the pcm with the newest software (based on your vin) you will be able to re read the file and license it
so i have to delete the config file then enter the app key then delete the file ,then enter the old key
so so you want me to start a new thread in requests for a easier method or should we move...
I'm not sure if this has been requested before but i would like the ability to use the scanner with a different cable it will not let you connect (invalid cable id #) you cant even pull logs from...
wonderful thank you for the fast reply
now i have some smoke to make :D