Search:

Type: Posts; User: Mbrowning

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I the last few I tuned, I used the Blue Cat...

    I the last few I tuned, I used the Blue Cat software to set up my tables. There are some videos on youtube showing how to use them. Good stuff.
  2. Replies
    6
    Views
    83

    Probably wouldn't hurt to check your connections...

    Probably wouldn't hurt to check your connections at the MAF sensor. This looks like a good time to invest in a wideband if you don't already have one. Something's obviously not reading right.
  3. It took a minute, but I think I found it. Your...

    It took a minute, but I think I found it. Your vve table looks jacked up for some reason. Looks like someone was tuning and quit halfway through. A table that rough is going to cause you all kinds of...
  4. Replies
    11
    Views
    594

    1-2 flare correction

    Here you go brother...
  5. Replies
    9
    Views
    412

    giffincox, normally when the blade is wide open,...

    giffincox, normally when the blade is wide open, PID will show 89% for some reason.
  6. Replies
    9
    Views
    412

    Still closing, but did you try returning the...

    Still closing, but did you try returning the torque tables to stock?
  7. Replies
    9
    Views
    412

    I believe Russ Kemp commented on a post similar...

    I believe Russ Kemp commented on a post similar to this in the past. Believe it or not, the fix for the problem was leaving the vtt and torque tables alone. He also advised leaving the dd tables...
  8. Replies
    6
    Views
    366

    Looks like you added your burst retard back. Then...

    Looks like you added your burst retard back. Then you bumped your minimum spark table to 21 degrees at wot. Not smart. You need to take your minimum spark table back and pull timing in the areas that...
  9. Replies
    1
    Views
    131

    Under the oxygen sensor tab go to "fuel control"...

    Under the oxygen sensor tab go to "fuel control" and it's on dual bank. Set it to disabled.
  10. Replies
    6
    Views
    366

    The 4800 rpm area is very prone to knock. It's...

    The 4800 rpm area is very prone to knock. It's normal to see a couple degrees less timing in this area from .60 to wot. Most of your table looks a little high to me unless your are running some...
  11. The P182e code is for the internal mode switch....

    The P182e code is for the internal mode switch. (Tells tcm which gear you select) The p1915 is directly related to 182 code. Those codes will only set if the tcm sees voltage at the transmission. It...
  12. Replies
    6
    Views
    266

    Post a file for us to look at. A log would help...

    Post a file for us to look at.
    A log would help too.
  13. Replies
    9
    Views
    482

    If you get a mdi 2, you can buy a 3 day...

    If you get a mdi 2, you can buy a 3 day subscription to gds2 and do it yourself. Very handy tool to have when you do a bunch of programming and need a solid pass thru.
  14. Replies
    51
    Views
    3,544

    The TRRL settings made my truck react quicker,...

    The TRRL settings made my truck react quicker, and that's it. Makes me feel like i'm in a lighter vehicle. I'm pretty sure it shouldn't be causing a stumble.
  15. Replies
    3
    Views
    255

    I am only seeing the engine side of the...

    I am only seeing the engine side of the calibration.
  16. Replies
    9
    Views
    482

    I'm curious to see how these look before I drop...

    I'm curious to see how these look before I drop $700....ouch
  17. Replies
    11
    Views
    594

    Here's something for you to look at. I hope some...

    Here's something for you to look at. I hope some of it helps.
  18. Replies
    11
    Views
    594

    I would be glad to look at your stock file and...

    I would be glad to look at your stock file and make some changes for you to look at. Would you mind uploading it?
  19. Replies
    8
    Views
    273

    The engine will be much more responsive with...

    The engine will be much more responsive with timing in the 16-22 range, however, if you like the way it sounds at 8 then leave it. Just remember that the lower you drop your timing from "ideal", the...
  20. Replies
    51
    Views
    3,544

    I think you're gonna like it.

    I think you're gonna like it.
  21. Replies
    51
    Views
    3,544

    Other than my truck feeling more responsive, I...

    Other than my truck feeling more responsive, I notice that the transmission is a little more aggressive when downshifting. I guess you could add a little to decel and correct this. One negative, if...
  22. The p0700 is a serial data code for information...

    The p0700 is a serial data code for information only. Being a fresh module, i'm guessing you probably have the wrong calibration loaded. The p0711 is a fluid temperature code. This code may have...
  23. Replies
    51
    Views
    3,544

    I uploaded the new beta today. The new settings...

    I uploaded the new beta today. The new settings were there, so I tried them. Very pleased with the results. Thanks for starting the thread Higgs Boson!
  24. I'm sticking to my guns on this one. It is not...

    I'm sticking to my guns on this one. It is not necessary to tune a factory vve table to put a set of headers on. Will it help? Yes. How much? Probably not enough to notice. The factory does a pretty...
  25. You can go either way. With just headers, I would...

    You can go either way. With just headers, I would run Maf only above 800.
Results 1 to 25 of 48
Page 1 of 2 1 2