Search:

Type: Posts; User: RandomEnthusiast

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds; generated 30 minute(s) ago.

  1. Replies
    2
    Views
    1,740

    The only way I'm seeing to enable at idle would...

    The only way I'm seeing to enable at idle would be drop eot and ect enable temps to below normal operating range. Other than that there doesn't seem to be another way to kick on with a/c enabled. I...
  2. Replies
    4
    Views
    5,193

    If not custom tunes you can pull canned tuned. I...

    If not custom tunes you can pull canned tuned. I would start with stock read and compare to a canned tune for reference of tricks they use. You have ficm tuning you can use so definitely use it. ICP...
  3. Most toyota's use a 0-5volt planar sensor so...

    Most toyota's use a 0-5volt planar sensor so technically a wideband but really better off having 2 data points because factory sensors can be limited in capabilities. I think most vehicles 2010 plus...
  4. Replies
    3
    Views
    6,168

    Might have popped the fuse for the compressor. Or...

    Might have popped the fuse for the compressor. Or melted it. Seen that before on a locked up compressor. Could be cycling switch.
  5. Replies
    3
    Views
    6,168

    You have more than likely a 5 volt...

    You have more than likely a 5 volt rail(reference) shorting to ground causing the voltage to drop. Seen something similar with a DPFE sensor shorted internally causing all sorts of havoc. The person...
  6. Replies
    2
    Views
    1,793

    Don't. I would advise against it. It could be a...

    Don't. I would advise against it. It could be a totally different strategy and brick your stuff.
  7. Is the pcm/ecm still black oak based or did they...

    Is the pcm/ecm still black oak based or did they use another unit? If it's black oak based maybe try swapping a ford pcm in.
  8. For basics I would check out some of the duramax...

    For basics I would check out some of the duramax stuff. Granted completely different than the ford stuff it still correlates with pulse width etc. Your timing for bowl swirl on the piston etc. I...
  9. A fellow slop I see. As someone else said if...

    A fellow slop I see. As someone else said if you're not running 2 bar or something of the nature I would switch to that first. Or you can try lowering the pulsewidth limit. I don't have vcm installed...
  10. I know it's a long shot but any plans for 2AZ-FE...

    I know it's a long shot but any plans for 2AZ-FE 2.4l post 05 support? Just wondering. Got a camry that could use some pep and the trans acts funky when I run it more than 1000 miles without...
  11. Replies
    7
    Views
    7,164

    EOT being high is pretty normal on 6.0ls. It's...

    EOT being high is pretty normal on 6.0ls. It's the same way with 7.3ls. They go by EOT since it's a hydraulic oil system. The Cooling system isn't that great. I've seen plenty of thermal issues with...
  12. Replies
    1
    Views
    4,190

    You're gonna have to segment swap probably. Do...

    You're gonna have to segment swap probably. Do you have a tac module hooked up? Is your pcm even capable of dbw? As far as I know the p01 should do dbw but p59 is better for it. If you don't have a...
  13. Replies
    7
    Views
    7,164

    The reason why ect is disabled is it relies on...

    The reason why ect is disabled is it relies on eot temps only pretty much. Since it's a high pressure oil system they had the pcm essentially ignore ect. I haven't played with it to much but lowering...
  14. Replies
    5
    Views
    4,381

    Hmmmmmmm. Idk.

    Hmmmmmmm. Idk.
  15. Replies
    5
    Views
    4,381

    Are you hitting the brake? Sounds like a stupid...

    Are you hitting the brake? Sounds like a stupid question but that pretty normal behavior you're seeing. No lockup on decel is normal across pretty much everything.
  16. Replies
    1
    Views
    1,545

    EBP I would think.

    EBP I would think.
  17. Replies
    3
    Views
    4,515

    Normal on all pedals from gm to bmw. It's normal...

    Normal on all pedals from gm to bmw. It's normal to see 15-20% tps at idle. You want to pay attention to actual. Because the pcm automatically re zeros the sensor from my experience. Same thing on...
  18. Replies
    6
    Views
    2,324

    Have you done pwm on injectors yet on the ficm?...

    Have you done pwm on injectors yet on the ficm? Can you ramp in more pressure faster in the hpop tables?
  19. I dont like to be connected to anything outside...

    I dont like to be connected to anything outside of the vcm cable when reading or flashing. But see if 351c is right.
  20. Replies
    6
    Views
    7,888

    That's awesome. Hopefully you can figure out more...

    That's awesome. Hopefully you can figure out more stuck. ATM I don't have anything to test anything on so yay me.
  21. Replies
    6
    Views
    7,888

    Injection timing and scaling back pedal map and...

    Injection timing and scaling back pedal map and mass fuel desired went from 16 hwy on 06 250 to 19hwy on same truck. I scaled it back by about 15% fuel wise and bumped timing 2 degrees.
  22. Replies
    4
    Views
    7,966

    I think the 0411 is the most used because it's...

    I think the 0411 is the most used because it's the most available. It's in everything and can run almost anything gm sbc gen 3 24 and dizzy stuff to.
  23. Replies
    21
    Views
    20,204

    Huh. Ok. I thought it was the other way around....

    Huh. Ok. I thought it was the other way around. Ohh well. Now that I know that I'll look at ebp tables.
  24. Replies
    21
    Views
    20,204

    As far as I know the EBP isn't used for boost...

    As far as I know the EBP isn't used for boost post 04 late. But it could have an older strategy.
  25. Replies
    21
    Views
    20,204

    Use open loop vgt controls to increase boost.

    Use open loop vgt controls to increase boost.
Results 1 to 25 of 334
Page 1 of 14 1 2 3 4