Search:

Type: Posts; User: castorjames

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. thank you, i been trying to contact a2speed...

    thank you, i been trying to contact a2speed without any luck. i wanna send trx pcm to put jeep VIN and turn off SKYM.

    how are they using that pcm in a gpec5 equipped vehicle?? they offer the...
  2. 2020 jeep demon swap

    hello any more info on this?

    attached is a file from a 2020 jeep wrangler with demon swap.
    it looks like it uses custom Operative system in both ECM and TCM??
    any help in who can do this kind...
  3. can you turn skym off and changue vin on a...

    can you turn skym off and changue vin on a 2022-2023 trx pcm? currently working on a 2023 gladiator , installed a hellcat engine , any info on what other companies are doing for this swap? thanks
  4. Replies
    0
    Views
    232

    2023 jeep Mojave hellcat swap

    Hello, doing a hellcat engine/trans swap on a 2023 jeep mojave ..
    Any one knows what ecm/tcm calibration to use?
    I think a 2023 ram trx cal would be the way to go ? Any help would be apreciated
  5. Replies
    5
    Views
    685

    hello, did you wire?: PIN:...

    hello, did you wire?:

    PIN: 3-----TN/WH-----Axle Switch Signal
  6. Replies
    0
    Views
    314

    2020 e90 bench flashing?

    Is There any special way to read/flash those ecm in bench harness? 2020 swap i can read it but cant flash it. Installed ecm in a normal truck and was able to read/write.. what Wires for vence harness...
  7. it uses the stock throttle body. yes i did turn...

    it uses the stock throttle body. yes i did turn back to stock almost all throttle tables and driver demand tables because was testing the throttle oscilation and the WOT body lag without any succes....
  8. 2020 jeep magnuson throttle oscillation and throttle WOT delay

    throttle body start to oscillate when map goes 1-2 psi of boost at part throttle. also it takes some time until throttle body goes full open.
    any help? thanks
  9. Replies
    2
    Views
    527

    yes, just wanted to start with magnuson file as...

    yes, just wanted to start with magnuson file as base, already sent email to magnuson as per their instructions but didnt received it yet, i got this 2018 jeep magnuson file, it worked fine as base.
  10. Replies
    2
    Views
    527

    looking for 2020 jeep magnuson file

    hello looking for magnuson provided calibration for 2020 jeep gladiator. thanks
  11. i have worked with him many times before for...

    i have worked with him many times before for remote tune service and other times just looking for help and hes been there. Gen V, ford and dodge.
    i dont think this is the way to resolve your...
  12. share please

    share please
  13. Replies
    2
    Views
    915

    2021 ford 6.7l tune needed

    hello, looking for a tune for a 21 ford 6.7l superduty, need it for today, pcm already unlocked. send me PM thanks
  14. Go to : ENGINE...

    Go to :
    ENGINE DIAG-------------AIRFLOW--------------------MAXMAP(45635)---------------set to 195kpa
    this will prevent the map to read higher than 200kpa and will avoid the limiter.

    how much...
  15. Replies
    40
    Views
    7,262

    who can share a picture of those tables? cant...

    who can share a picture of those tables? cant find em.

    Three other directly related tables are under your torque model tab - they are airflow for high, low and mid altitudes - these will do the...
  16. Thanks . Speed density calculator is treated like...

    Thanks . Speed density calculator is treated like gm VVE? Need to pay attention if model goes weird when calculating the table? What others pids will help with fuel logging ? Thanks in advance
  17. Thanks sultan. I'll shoot you a pm

    Thanks sultan. I'll shoot you a pm
  18. 2019 whipple 3.0l stage2 132mm TB ____HOW TO CORRECT FUELING?

    Hello, what is the correct place to correct fueling on 2019 f150 trucks?, speed density calculator?? and what is the correct way to use it? thanks
  19. Help. Auto to Manual. what is the correct procedure?

    Attached is the file of the car, it is a 2014 jeep with hellcat engine.
    its setup with a 4l80e trans now.

    What would be the best aproach here?
    Do i need to changue in the tune for manual trans?...
  20. Replies
    13
    Views
    1,498

    make sure your swap has the correct high pressure...

    make sure your swap has the correct high pressure sensor for your app. 3 pin vs 4 pin. double check the 2 connectors that goes behind intake. they can be mixed and will make this issue
  21. set your gap to .019 and you will be golden.. i...

    set your gap to .019 and you will be golden.. i just tuned 1 of those, really close s etup. it started to blow spark at 10 psi with gap at .035
    make sure you have the correct spark plugs, the ones...
  22. Today ill teSt another truck. it haS the Same...

    Today ill teSt another truck. it haS the Same iSSue, weird to drive becauSe of the throttle body (it haS magnuSon Sc). ill Share reSultS, hope thiS make the trick again.
  23. dizable torke converter in the tune; part...

    dizable torke converter in the tune; part throttle/wot. when you done then you can ztart tuning tcc to your like, how iz it zhifting at part throttle?
    pleaze check your tranz oil level, overfill...
  24. put your ztock tranz tune, mod your zhift...

    put your ztock tranz tune, mod your zhift zchedulez and RPM, up the tranzmizzion prezzure trezholdz, DO not reduce or remove tranz torke management, i can zee you lowered multiplierz on tranz torke...
  25. Replies
    33
    Views
    6,505

    truth x100

    truth[/quote]

    x100
Results 1 to 25 of 294
Page 1 of 12 1 2 3 4