Search:

Type: Posts; User: Jabbott

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    325

    Had this happen once on a Trailblazzer SS with...

    Had this happen once on a Trailblazzer SS with the E40. I thought I bricked it for some reason. I ended up putting it on a bench harness and reflashing. Put it back in the truck and it was fine....
  2. Replies
    2
    Views
    904

    Any word on adding support for the ECM AFM1500...

    Any word on adding support for the ECM AFM1500 Wide Band
  3. Thread: 525 ls3

    by Jabbott
    Replies
    6
    Views
    266

    Thank you mjm350. I did try adapting your tables...

    Thank you mjm350. I did try adapting your tables into my calibration and it does not want to start. Only a couple of tables looked different and I didn't modify my TB tables. I am going to go back...
  4. Thread: 525 ls3

    by Jabbott
    Replies
    6
    Views
    266

    Well because you can't set where the TPS runs,...

    Well because you can't set where the TPS runs, that is where it is stable. Yes, LSX 376, PO1 ECM, there is no IAC motor, its' part of the 90mm tb. This is a blended VE/MAF calibration. I can't adjust...
  5. Replies
    2
    Views
    1,150

    I have a 2006 CTSV file that was my 6.0L with the...

    I have a 2006 CTSV file that was my 6.0L with the ASA cam in it. It will be a little different but just start with your stock cal. Add 20% to the MAF and remove 10% from The VE table to start with....
  6. Thread: 525 ls3

    by Jabbott
    Replies
    6
    Views
    266

    525 ls3

    So I am kinda of embarrassed to say that I may have bitten off more than I can chew with this one. I installed a 525 engine in a 03 auto C5. All of my steady state tables are close to lambda 1,...
  7. Replies
    94
    Views
    13,785

    Pretty excited about the upgrade

    Pretty excited about the upgrade
  8. Replies
    179
    Views
    57,880

    Is the ECM AFM 1500 serial WB setup now on the...

    Is the ECM AFM 1500 serial WB setup now on the software now?
  9. Replies
    2
    Views
    841

    I don't have it on this PC. It shows it happening...

    I don't have it on this PC. It shows it happening in the log, the fuel bounces around a little but it is being caused by something the secondary. The fuel is good timing goes stable but the RPM do no...
  10. Replies
    9
    Views
    1,328

    Why would you use such a large injector when a...

    Why would you use such a large injector when a small one is needed. You get too large and it will not idle well no matter how good the data is.
  11. Replies
    3
    Views
    1,603

    Pretty sure calibrated success has it in their dvd

    Pretty sure calibrated success has it in their dvd
  12. Replies
    2
    Views
    841

    Weird throttle hesitation

    04 GTO with a SD conversion. This is a drag car, so when you bring the throttle up to 2200RPM and launch the car will not accelerate immediately it feels like it is on a rev limiter which it is not....
  13. Replies
    9
    Views
    1,328

    The ID injectors are too big for what you are...

    The ID injectors are too big for what you are looking for. But most all companies data is stolen from other data which doesnt work. Zip has 58lbs injectors with real data that Greg Banished helped...
  14. Replies
    7
    Views
    2,201

    Keith, I had one opened. However we fixed it this...

    Keith, I had one opened. However we fixed it this morning. A couple of weeks ago I had a second monitor plugged into my laptop. Even though it is disconnected and setup for one monitor, when you...
  15. Replies
    11
    Views
    3,369

    I understand but you end up spending a ton of...

    I understand but you end up spending a ton of time working on something that will never really be right. We all do it and end up working allot of hours before just putting the right part in. Save...
  16. Replies
    11
    Views
    4,924

    Bosch ECU, may not be so easy to get into

    Bosch ECU, may not be so easy to get into
  17. Replies
    5
    Views
    1,600

    oh I see it. I was using the quick reply and it...

    oh I see it. I was using the quick reply and it doesn't allow attachments.
  18. Replies
    11
    Views
    3,369

    I don't think it is a good injector to use period...

    I don't think it is a good injector to use period because of this. Same with using the ford 47's with split spray. You would be better off using a set of deka 60's. You will have some wall wetting...
  19. Replies
    11
    Views
    3,369

    Yes it is, which effects tip in throttle and...

    Yes it is, which effects tip in throttle and really all throttle including transient.
  20. Replies
    5
    Views
    1,600

    Wow that came out real small. send me your email...

    Wow that came out real small.
    send me your email and I will email you the spreadsheet
  21. Replies
    5
    Views
    1,600

    59011

    59011
  22. Replies
    5
    Views
    1,600

    I do it the hard way or so it may seem. If you...

    I do it the hard way or so it may seem. If you make a excel spread sheet just like above but next to the 408 put in 400 also. The 400 represents 4 bar or 58 psi. Now if you put in your 64lbs and you...
  23. Replies
    11
    Views
    3,369

    Have you changed anything in the wall wetting...

    Have you changed anything in the wall wetting settings. I think the Maggie fuel injection hole is dead center of the intake. The LS9/LSA injector has a 20 degree offset in the spray pattern so if you...
  24. Replies
    4
    Views
    1,303

    Reading the tune should have no effect on it. I...

    Reading the tune should have no effect on it. I have been disconnected while downloading a cal and it still works. Now uploading it can be an issue if it is interrupted.
  25. Replies
    7
    Views
    2,201

    Just downloaded .108. Exact same thing going,...

    Just downloaded .108. Exact same thing going, there has to be an explanation for this. It was working up until I downloaded .103 now if I do anything it is locked up. what is going on?
Results 1 to 25 of 224
Page 1 of 9 1 2 3 4