Search:

Type: Posts; User: Russ K

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Actually, you get a 75% (rounded down) trade in...

    Actually, you get a 75% (rounded down) trade in towards a model year license. So it takes more than 6 credits for a model year if you're just licensing one vehicle at a time.

    Russ Kemp
  2. Replies
    7
    Views
    202

    I can't open your tune, a dialog box says...

    I can't open your tune, a dialog box says "Translating Tune unknown source" But besides the Map dropping at WOT, your Bank 1 O2 MV is dropping. Looks like there is a misfire on Bank 1.

    Russ Kemp
  3. Replies
    3
    Views
    237

    The throttle is closing at 3900 RPM. Disable the...

    The throttle is closing at 3900 RPM. Disable the ETC limit in the Cutoff, DFCO tab.

    Russ Kemp
  4. Replies
    29
    Views
    6,747

    The 2008 Sierra that I replied to does. You need...

    The 2008 Sierra that I replied to does. You need to set all DoD codes to no error reported, uncheck the SES box, and change the DoD to disabled.

    Russ Kemp
  5. Replies
    29
    Views
    6,747

    You need to disable P3400 Russ Kemp

    You need to disable P3400

    Russ Kemp
  6. Replies
    174
    Views
    82,244

    Your PE is set to 14.7, I would change it to...

    Your PE is set to 14.7, I would change it to 11.5. Also, you need to raise the PE enable TPS. Yes, on some vehicles the commanded AFR will still move around even after setting the open loop AFR adder...
  7. Thread: P0300

    by Russ K
    Replies
    18
    Views
    388

    Yes, a lean condition due to intake gasket leak...

    Yes, a lean condition due to intake gasket leak (very common on the 5.3 & 6L trucks) can cause 7 & 8 to misfire. Any Maf DTC disables the misfire counters.

    Russ Kemp
  8. Replies
    2
    Views
    347

    The Ballenger has a 9-16 AFR range as standard....

    The Ballenger has a 9-16 AFR range as standard. Are you selecting it, or are you selecting the wide range one?

    Another thing to test, is remove the wide band from the channels. Then just insert...
  9. Replies
    36
    Views
    18,675

    I assume that you installed a none DoD valley...

    I assume that you installed a none DoD valley cover? If so, then you must set all of the DoD codes to no error reported & uncheck the SES box.

    Russ Kemp
  10. For the Lambda error to function, just select the...

    For the Lambda error to function, just select the EQ Ratio Error in the Maths Folder. As for the spark knock, you will need to use 93/94 octane fuel.

    Also your engine temp is very hot. Use a 160*F...
  11. Replies
    20
    Views
    827

    I lean out the closed loop AFR. Set the Max...

    I lean out the closed loop AFR. Set the Max Rich/Lean to 200 MV (ECM 2519)

    Russ Kemp
  12. Replies
    2
    Views
    179

    That's because you don't have a wideband in your...

    That's because you don't have a wideband in your channels.

    Russ Kemp
  13. Your tune shows 3.73 gears & a 21.43 dia tire. ...

    Your tune shows 3.73 gears & a 21.43 dia tire.

    Russ Kemp
  14. Go to trans>General>Transmission Protection>Lower...

    Go to trans>General>Transmission Protection>Lower Clip. Stock is at 1500 RPM, raise it. Also look at your Max Throttle vs Rpm, put the 0 & 500 RPM to 90*

    Russ Kemp
  15. https://forum.hptuners.com/showthread.php?14186-Th...

    https://forum.hptuners.com/showthread.php?14186-The-curse-of-the-P0121-Code&highlight=curse+P0121

    Russ Kemp
  16. Replies
    9
    Views
    432

    This is the Full Throttle TCC tables that support...

    This is the Full Throttle TCC tables that support added for me.

    Russ Kemp
  17. Replies
    12
    Views
    381

    That's not what I said. Look in the engine...

    That's not what I said. Look in the engine diagnostic tab.

    Russ Kemp
  18. Replies
    12
    Views
    381

    You must do a write entire for the TCS patch to...

    You must do a write entire for the TCS patch to work. If you already did that, then you most likely are getting the P0106 code due to your cam shaft. To fix that, disable the P101, P0106 & P121 test...
  19. Replies
    9
    Views
    432

    Ask support to add the Full Throttle TCC tables....

    Ask support to add the Full Throttle TCC tables. I had support add these tables to a 2000 6L 4L80E Silverado.

    Russ Kemp
  20. There's your problem. Get the exhaust system...

    There's your problem. Get the exhaust system built. As any exhaust leak close to an O2 sensor will cause positive fuel trims & fouled spark plugs.

    Russ Kemp
  21. Sport mode, I think it's pattern A. To test, set...

    Sport mode, I think it's pattern A. To test, set pattern A shift speed table to 100 MPH, put the car in sport mode. If the trans won't upshift, you're using pattern A.

    Russ Kemp
  22. Replies
    21
    Views
    700

    The TCC will not apply until the trans fluid temp...

    The TCC will not apply until the trans fluid temp is warmed up. As for the cold flare, try adding to the temp offset table.

    Russ Kemp
  23. Replies
    11
    Views
    506

    Once I get the part throttle/low RPM shift...

    Once I get the part throttle/low RPM shift firmness right, then I keep lowering the 4800-6500 RPM columns by 10% at a time. I have .152 in the bottom right of the 1-2 shift & .209 in the bottom right...
  24. Replies
    11
    Views
    506

    The 2016 5.3/8 speed, has the exact shift...

    The 2016 5.3/8 speed, has the exact shift pressures as your truck. Just set up the shift pressures as I suggested & fine tune with the shift times.

    Russ Kemp
  25. Replies
    11
    Views
    506

    I used to believe that, but I can make the shifts...

    I used to believe that, but I can make the shifts violent without touching the Max Pressure table. I'm thinking the Max Pressure table is the max pressure on top of the Base Shift pressure that is...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4