Search:

Type: Posts; User: GrannySShifting

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    839

    Most E38 have this setting

    Most E38 have this setting
  2. Replies
    9
    Views
    839

    Anyone?

    Anyone?
  3. Replies
    79
    Views
    26,272

    Sticky: They call it vaporware I think? :banghead:

    They call it vaporware I think? :banghead:
  4. Replies
    14
    Views
    1,038

    Change the Delay Volume and Transition Volume to...

    Change the Delay Volume and Transition Volume to 0 - sometimes takes long time for it to realize change in content with stock settings
  5. Replies
    18
    Views
    4,205

    Can you post up what you ended up with?

    Can you post up what you ended up with?
  6. 2012 CTSV, cant even log MAP raw voltage?

    Scanner maxes at 255 kPa reported, on others I just log MAP raw voltage and you can figure out from there depending on what MAP your using, but scanner doesnt even show that as an option?:banghead:
  7. After digging around it that's what I was...

    After digging around it that's what I was assuming. I can physically scale three axis so it can read a LS9 map, but does that work as it should?

    This must have been done with an OLD version of...
  8. I had to refresh the page, guess it kept the post...

    I had to refresh the page, guess it kept the post and I didnt notice it didnt keep the attachments??
  9. 2015 SS but virtual VE isnt in edit menu like normal, in reg tables?

    Whats deal with this
  10. Replies
    2
    Views
    223

    Factory line lock

    Can this be enabled with HPTuners, supposedly somethign called Tazer can add the function plugged into OBDII port
  11. I was never able to figure this one out

    I was never able to figure this one out
  12. Replies
    0
    Views
    354

    0-5v sensor noise

    Logging on OEM pcm some of the pressure sensors dont have clean readings. Is there some way to clean these up so they log a little more stably? The factory pressure sensors on these inputs (fuel tank...
  13. Think he jumped off nearest cliff. in car.

    Think he jumped off nearest cliff. in car.
  14. Worried about the Hemi powered stuff mainly

    Worried about the Hemi powered stuff mainly
  15. The earlier versions of these have no flex sensor support correct?

    Are there any 0-5v inputs that can be used to influence fueling etc? I think Ive seen some work arounds people are trying?

    When and what ECUs started getting flex capable support?
  16. That 156 is IS the one I usually use. I guess I...

    That 156 is IS the one I usually use. I guess I just forgot about the old ones not having it until it actually showed up as a problem? Guess I'm going to copy everything over into one of those OS...
  17. So does it have a built in delay and you just...

    So does it have a built in delay and you just can't access it? Or it shouldn't have that and I should be looking elsewhere? Its got to have it because you can see target air fuel take while to switch
  18. Ended up w/ OS that doesnt have Power Enrich rate??? 9381344 OS

    Chasing a knock on tip in no matter what I do, then it finally dawned on me that I wasnt seeing the PE Rate table. Im so used to automatically setting that to 1.0 from .0195 or whatever the factory...
  19. I dont think running e85 will clean it up...

    I dont think running e85 will clean it up anything like seafoaming it will

    That prob what Id do split it 87 and ethanol.
  20. Tried another sensor, same thing, has good...

    Tried another sensor, same thing, has good continuity from signal out to pcm, 12 volt and ground checks out fine...
  21. Hello, and welcome to 2010 Bob haha The newer...

    Hello, and welcome to 2010 Bob haha

    The newer 5.3s make a good bit more than the old ones, have higher static compression etc They will not take 28-30 degrees timing like some of the old ones...
  22. Gen3 PCM flex enabled but doesnt recognize?

    Same ECU and base OS Ive used on half dozen others. Even setting the default percentage to 10% it still shows 0% alcohol content which doesnt make sense either :banghead: When I use the config I...
  23. Sanity check, offset/linear for 3.5 Bar AEM/Holley MAP

    Linear is range over 5 volts, it can read 345 kPa from .5 to 4.5 (86.25 KPa-volt) so linear needs to be 431.25

    It is 0 kPa at .5 volts so the offset needs to be half of the 86.25 kPa-volt so...
  24. Replies
    3
    Views
    190

    Are 2012 Rams supported?

    Doesnt seem to be by the vehicle list
  25. These don't do anything other than go lean when...

    These don't do anything other than go lean when dutycycle gets up there, and this was still controllable air fuel
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4