Search:

Type: Posts; User: raulhp

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    1,553

    djyankees31 I spoke with the company who did...

    djyankees31

    I spoke with the company who did the pulley, they use other system to tune the Jaguar Ecu, they told me that HP tuners gets may PIDs with wrong values, but it is not its problem, comes...
  2. Replies
    12
    Views
    1,553

    Yesterday i was testing with bigger changes in...

    Yesterday i was testing with bigger changes in the tables. Good results.
    I could see the boost rise from 0.8 bar to 1.3 bar. that is because you need rise the torque to load table, torque limits,...
  3. Replies
    12
    Views
    1,553

    hello I tested today the car with the new pulley...

    hello
    I tested today the car with the new pulley at WOT. I found that i dont have knock anymore.

    but very disapointed because i could see the Boost is exactly the same as STOCK, i assume the...
  4. Replies
    12
    Views
    1,553

    Hi to all I installed the new crank pulley,...

    Hi to all

    I installed the new crank pulley, but before that i did a log. I could see the stock calibration retard about 2/4 degrees timing just when you push the throttle to 100%, around 3000rpm,...
  5. Replies
    12
    Views
    1,553

    i will install the pulley next week. i had a oil...

    i will install the pulley next week. i had a oil leak from the crankshaft grommed and it is in the workshop
    I did the base map with the new limits and torque requests. Need install the pulley and do...
  6. Replies
    12
    Views
    1,553

    I will test my new Pulley in the Jaguar, anyone...

    I will test my new Pulley in the Jaguar, anyone insteresting on results? HP tuners got me more limits tables to rise them and avoit limits. My crank pulley is for about 80HP more.
    Car works with...
  7. Replies
    0
    Views
    307

    Back to Stock Ecu

    Hello,
    I assume this question is simple but i didnt find an answer on the forum

    i want do some test in a Jaguar F-type 3.0 supercharger, with a new crank pulley, a bigger one. It is a test mule...
  8. Replies
    5
    Views
    2,536

    I am also interested to see a tune file to...

    I am also interested to see a tune file to understand what they changed.
    I have a jaguar F-Type V6 with a smaller crank pulley and i want tune it, this will rise the power 100hp, so will be a lot.
    ...
  9. Replies
    12
    Views
    1,553

    The problem is we dont have any Jaguar specialist...

    The problem is we dont have any Jaguar specialist here, in Spain, no also jaguar specialist, even HP tuner specialist and that is the reason from my question. I am Engine calibrator for race cars...
  10. Replies
    12
    Views
    1,553

    Jaguar F-type 3.0 Supercharger 2017

    Hello to all

    i own a 2017 Jaguar F-type, i will install a Crank pulley to get more boost from my Supercharger. As i never tuned this car, and i didnt know how it works. I will be really pleased if...
  11. Here you have?.

    Here you have?.
  12. No, injectors are stock. Minimum injector pulse...

    No, injectors are stock.
    Minimum injector pulse is 1.2 ms and I have between 2,8 / 3.2 all time
  13. sorry, i did not have any log saved, but o2...

    sorry, i did not have any log saved, but o2 voltages were around 0.6 volts...
  14. ridiculous Rich at idle, No changes editing tables...

    Hello to All

    I'm Raul from Spain, I have a customer with a Corvette C6 (LS7) with high Cams and high compression piston. This customer send to US (yes the car, not the engine) to be tuned. THis...
  15. Thanks I found it just after wrote this post...i...

    Thanks
    I found it just after wrote this post...i read it carefully and i will do what it says
    Thanks again
  16. hi again My customer told me that drove for...

    hi again
    My customer told me that drove for about 20min and the DTC came again, P1516...and no throttle at all. i lowered the m?ximum angle to 95% but still there...
  17. Well, today i tested...if i go to DTC and put to...

    Well, today i tested...if i go to DTC and put to no report...the car goes to limp mode again...but you couldn't see on the Scanner, you could delete them, but you could see them.

    But...i tried...
  18. i did not tested, will try for you, the owner...

    i did not tested, will try for you, the owner ordered a new pedal and throttle motor
  19. Hello schpenxel I when to advance view...:o and...

    Hello schpenxel
    I when to advance view...:o and i checked MAF Limit Vs RPM table, we have a stock limit of 300 g/s, our engine gets 447 g/s, so i rised the limit to 550 g/s to be sure, after this,...
  20. i feel stupid right now...will do

    i feel stupid right now...will do
  21. Hello schpenxel, I went to test the value you...

    Hello schpenxel,
    I went to test the value you told me, but our HP tuner version does not have it, my customer has the Standard version, we called to another guy to ask and said the same, may be the...
  22. The Pedal is the corvette one. All new and come...

    The Pedal is the corvette one. All new and come with the engine and wiring like a "plug and play" set.
    Will test the P0068 and put 8192.

    About P0102, i did not check the frequency, it is with the...
  23. LS3 DTC MAF/Throttle Problem (all new and untuned)

    Hi to all.

    My name is Raul, i live in Spain, so there are not many LS engines here. One of my customers has done a LS3 swap in a Nissan 350z, so we went to all new Crate engine with stock wiring...
Results 1 to 23 of 23