Search:

Type: Posts; User: 2therock

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thank You Tons Coanan. Without your help I would...

    Thank You Tons Coanan. Without your help I would have had to flat bed the car to the shop 1hr:15 minutes away. I would not be using the Cometic gaskets, and would have had some additional rattled...
  2. OK, Mustang Dyno numbers are 412Hp / 430Tq. Just...

    OK, Mustang Dyno numbers are 412Hp / 430Tq. Just breaking over 6 PSI boost.
    For Dyno-Jet Fans a 12% adjustment would be 461.44 Hp / 481.60Tq.
    Its debated the Mustang dyno are the real numbers....
  3. AEM 30-0334 Boost Analog Logging, Need Help Converting the Volts to PSI w/MPVI

    Its been years and I'm rusty,
    I connected the + & - wires from the AEM 30-0334 boost gauge to the MPVI enhanced I/O and my gauge is reading in volts, not PSI and googling and pecking around has not...
  4. Replies
    10
    Views
    681

    I purchased HPT because of getting a rogue dyno ...

    I purchased HPT because of getting a rogue dyno tune on my FI Silverado.
    After asking around here I got extremely lucky and received a PM from a member offering help. He stayed with me for months...
  5. OK, I have sinned. I pushed her a little I...

    OK, I have sinned. I pushed her a little
    I configured the AEM 30-0334 OBD WB kit to scan. Very nice and easy, its what my tuner uses so he will like that, just plug into my OBD pass through for the...
  6. Its all buttoned up and ready for the Dyno with...

    Its all buttoned up and ready for the Dyno with me finishing up running the gauges. PITA but worth it. I really like the setup where it is.

    The penetrating oil I used on the exhaust manifold...
  7. Edit; Dyno on 2/21

    Edit; Dyno on 2/21
  8. The traction control icon finally off after I...

    The traction control icon finally off after I plugged in the brake booster lead I removed while wrestling to get the hose off during the install.
    Hooray, finally no faults, lights, or codes.
    ...
  9. While I was under there I pulled my O2 sensors...

    While I was under there I pulled my O2 sensors and the came free so I'm replacing all 4. With OE NTK units.
    I have a dyno tune appointment set up for 2/21.
  10. I cannot choose if I like it with the side covers...

    I cannot choose if I like it with the side covers or not. I guess I don't mind either way.
    The looming you see over the catch can hoses was tossed on the job by a vendor doing an installation. I...
  11. Little update. Bung hole drilled and fitted,...

    Little update.
    Bung hole drilled and fitted, getting it welded in the AM. New exhaust studs and nuts come in Tuesday. They same out so well I wanted to go back with dealership hardware.
    Sent...
  12. Thanks, the nuts spun off fine, then the studs, I...

    Thanks, the nuts spun off fine, then the studs, I was pleasantly surprised.
    New hardware will go back in. I seen a parts list with gaskets but see no evidence of that with the ball & socket thing...
  13. Next order of business, removing the left Cat to...

    Next order of business, removing the left Cat to have a bung welded in. Letting the fasteners soak now. How easy/hard did yours come off for the header install?

    Also, since I'm going to posses the...
  14. No headers. Shes going to stay as is. Just dialed...

    No headers. Shes going to stay as is. Just dialed in the best it can be. I'll go out and pick on Camry's and mini vans. :)
  15. Replies
    0
    Views
    129

    How Close Is Too Close For Wide Band o2?

    I have a 2013 Charger R/T I just installed a blower on w/stock exhaust manifolds and cats.
    I want to install an AEM OBD interface o2 sensor pre-cat but its a short run between the cat and the...
  16. Thanks, I have faith it will be as good as it can...

    Thanks, I have faith it will be as good as it can be after dustethoff tuning wrings it out on the dyno.
    So now I want to install a wideband pre cat but it's gonna put the sensor 6-8 inches from the...
  17. No limping. Smooth idle. No codes, I drove it...

    No limping. Smooth idle.
    No codes, I drove it about 8 miles, highway, Couple partial throttle
    romps.
    I'm worried about the trans with no tune so I'm not pushing it hard.
    It needs a tune pretty...
  18. Its Running! Dang it! I did not compare the...

    Its Running! Dang it! I did not compare the Diagnostic sections. You may have pointed to it and I didn't pick up on it but the thread I stumbled upon with the screen shots got me. I noticed the...
  19. Damn, call me hard headed, I did not compare in...

    Damn, call me hard headed, I did not compare in the Engine Diagnostics, and see Torque Delta and Misfire differences in addition to MAP settings.
  20. MAP Sensor Bingo! Thank You! I got home and...

    MAP Sensor Bingo! Thank You!

    I got home and metered the Edelbrock extension cable and its fine. I removed the Edelbrock MAP and my OE MAP fit & sealed into the hole fine and plugged it in....
  21. Ok on the map sensor. I'll do it tonight.

    Ok on the map sensor. I'll do it tonight.
  22. I'm worried the tune may have corrupted mp ecm....

    I'm worried the tune may have corrupted mp ecm. I'll keep trying.
    What is causing the etc to alarm?
    @work now, I'll do some as you say tonight. I have a co-worker bringing me a SCT unmarried, 5...
  23. The throttle body had to be installed on its...

    The throttle body had to be installed on its side, because of hitting the fuel rail and hose barb. Could this be it? I would need a spacer to rotate it back up.
  24. Well it got here and its on but it was not the...

    Well it got here and its on but it was not the problem. Same thing. The ETC light is flashing.
    I even flashed the factory tune to see if anything changed and nothing.

    I did manage to get HPT to...
  25. Tracker says TB here tomorrow. I'll be too busy...

    Tracker says TB here tomorrow. I'll be too busy to slap it on. Maybe late night tomorrow.
Results 1 to 25 of 461
Page 1 of 19 1 2 3 4