Search:

Type: Posts; User: Kill

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Awesome update, misfire minimum timing is finally...

    Awesome update, misfire minimum timing is finally explained...and now disabled. Thank you
  2. Replies
    143
    Views
    56,271

    I know "Torque CRV Limit" on my truck truck was...

    I know "Torque CRV Limit" on my truck truck was caused by reaching the max value in the pedal map.
  3. Replies
    143
    Views
    56,271

    I can't help you there, I haven't tuned an 04.5...

    I can't help you there, I haven't tuned an 04.5 up truck yet so I don't know about the baro problem. You obviously have a lot more tables/limiters in your 05 ecm so you may not have to disable them...
  4. Replies
    143
    Views
    56,271

    Bamofo, do you have any fuel quantity protection...

    Bamofo, do you have any fuel quantity protection factors under the Injection Quantity tab still enabled? I tried to leave some of those enabled at first but it wouldn't rev much over 4k rpm until I...
  5. Replies
    143
    Views
    56,271

    Or just disable pilot over 3000rpm since it...

    Or just disable pilot over 3000rpm since it really isn't needed up there anyway.
  6. Replies
    143
    Views
    56,271

    Tried, but I didnt see an option for attaching...

    Tried, but I didnt see an option for attaching tunes in a pm. The fact that it pulls out of it almost leads me to believe it may be a timing issue, as in too much timing in that range that it is...
  7. Replies
    9
    Views
    4,085

    What exactly is it doing? I know on mine half the...

    What exactly is it doing? I know on mine half the time I have to disconnect and then reconnect a few times before it starts working.
  8. Replies
    143
    Views
    56,271

    Alright, did some further testing. Raising the...

    Alright, did some further testing. Raising the extreme cut off up to 6000 didn't change much, still only made it to 4925 rpm. So to test the pedal map limit, I rescaled the pedal map to zero out at...
  9. Replies
    143
    Views
    56,271

    Early 2004, CM848

    Early 2004, CM848
  10. Replies
    4
    Views
    2,477

    Basically under light throttle and cruise...

    Basically under light throttle and cruise regions. Once load gets to around 25 percent the misfire minimum timing seems to drop into the negatives where it won't affect anything.
  11. Replies
    143
    Views
    56,271

    Here are pictures of where I had the limiters set...

    Here are pictures of where I had the limiters set at.
  12. Replies
    143
    Views
    56,271

    Very well could be, it was still pulling when I...

    Very well could be, it was still pulling when I let off but that could be because I let out of it right when the limiter was starting to kick in.
  13. Replies
    143
    Views
    56,271

    I'll take some screenshots, I had the enters...

    I'll take some screenshots, I had the enters maxed and the exits a couple hundred rpm lower. Also had the extreme cutoff still at 5500rpm.
  14. Replies
    143
    Views
    56,271

    What I basically did was max out all of the DFCO...

    What I basically did was max out all of the DFCO limiters and then used the pedal map to control max rpm by setting the last rpm column 100rpm higher than target and setting that column to all zeros....
  15. Thread: SOTF Tuning

    by Kill
    Replies
    71
    Views
    28,452

    I think he means switch on the fly tuning, like a...

    I think he means switch on the fly tuning, like a csp5 switch equivalent.
  16. Replies
    4
    Views
    2,477

    Figured I would bump this back up in case anyone...

    Figured I would bump this back up in case anyone can shed some light on it.
  17. Replies
    6
    Views
    3,291

    Try putting your Pilot Quantity ECT Coefficient...

    Try putting your Pilot Quantity ECT Coefficient table and your Pilot Timing ECTxIAT Coeffiient table back to stock.
  18. Replies
    29
    Views
    11,172

    The stock early 04 log I posted earlier in this...

    The stock early 04 log I posted earlier in this thread should have the same pilot tables as an 03.

    Take a look at this tune and log if you have time. If the pilot tables are max limiters, this...
  19. Replies
    15
    Views
    6,579

    It would be best to send your tuner the file with...

    It would be best to send your tuner the file with the OS patch. One time after applying the patch it would not allow me to load a pre-patch tune. I don't know if it was just being glitchy or that is...
  20. Replies
    29
    Views
    11,172

    If the output pilot SOI was the greater of the...

    If the output pilot SOI was the greater of the two, it would leave you with a theoretical 150* of pilot timing with the stock 04 maps if you were between 180-223 degress ECT and 80-100mm3 commanded...
  21. Thread: Timing Calculator

    by Kill
    Replies
    56
    Views
    29,738

    Thanks you for taking the time to make this up...

    Thanks you for taking the time to make this up and share it, much appreciated.
  22. Replies
    38
    Views
    13,357

    So what you're saying here is that you need to...

    So what you're saying here is that you need to subtract the base table timing value from the adder table value, and then apply the coefficient?
  23. Replies
    96
    Views
    32,398

    Could be, it is definitely close. FCA duty cycle...

    Could be, it is definitely close. FCA duty cycle desired seems to be pretty worthless, milliamps is the best way to see what the FCA is doing.
  24. Replies
    96
    Views
    32,398

    I don't think it is showing the milliamps,...

    I don't think it is showing the milliamps, although looking at old logs of my truck they are within 100 of each other. Mine was doing the same thing, but it would actually start creeping up to 12-13k...
  25. Replies
    96
    Views
    32,398

    Just for curiosity's sake, what is your lift pump...

    Just for curiosity's sake, what is your lift pump pressure at idle? After looking at this it looks like the ecm is trying to max the milliamps to the fca to keep rail pressure in check and it appears...
Results 1 to 25 of 57
Page 1 of 3 1 2 3