Search:

Type: Posts; User: aaronson

Page 1 of 13 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    815

    CJ/VMP twin69/PMAS

    Hello everyone and good eveing, I haven't posted in a while life tends to get a little busy sometimes. Nonetheless, I am having a P0223 code pop up pedal position sensor/switch B circuit high. Anyone...
  2. Thread: 2000 gt

    by aaronson
    Replies
    9
    Views
    1,516

    I really appreciate your information. I?ll talk...

    I really appreciate your information. I?ll talk to the guy and see what he wants to do. May just be a case where he has to get an SCT device for his needs. I suggested doing a plug n play standalone...
  3. Thread: 2000 gt

    by aaronson
    Replies
    9
    Views
    1,516

    No emissions aren?t an issue where I am, I just...

    No emissions aren?t an issue where I am, I just read someone else?s post where they let hptuners generate a vin and then the car wouldn?t start. To clarify when I connect to the car, it reads the...
  4. Thread: 2000 gt

    by aaronson
    Replies
    9
    Views
    1,516

    Would using the hptuners function where it...

    Would using the hptuners function where it generates the vin cause an issue. It?s able to read the stock tune file that?s on the car, there?s just no vin attached to it
  5. Also if you have the anti shuffle switch turned...

    Also if you have the anti shuffle switch turned on make sure it?s turned on until you get it 100% dialed, or just leave it off. That can cause issues sometimes
  6. Thread: 2000 gt

    by aaronson
    Replies
    9
    Views
    1,516

    2000 gt

    Vin not detected, has there been a nailed down solution to this, I don?t want it to generate a vin and cause an issue.
  7. Where in the exhaust are the 02 located?

    Where in the exhaust are the 02 located?
  8. There should be an inferred movement tab as well....

    There should be an inferred movement tab as well. I think it?s set to something like 3000 from the factory. I don?t have too much experience in transbrake setup but it makes sense to me if the pcm is...
  9. Replies
    5
    Views
    1,541

    You need a fuel system

    You need a fuel system
  10. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    A fuel system and e85 with more timing will put...

    A fuel system and e85 with more timing will put you over your goal no need for a throttle body. Those are half the cost to a fore innovations fuel system to support your goals. Just my opinion.
  11. Replies
    2
    Views
    13,716

    Couldn?t hurt to just throw some clutch packs in...

    Couldn?t hurt to just throw some clutch packs in it. Those go a long way, the transmission hardware itself it?s stout. At that horsepower range. You?re going about it the correct way. Most tuners...
  12. Replies
    4
    Views
    1,906

    I don?t know if you can disable it in the suite...

    I don?t know if you can disable it in the suite but you could always unplug the physical switch itself. I doubt you?d accidentally start it without pushing the clutch anyways.
  13. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    Yeah definitely not worth the time in my opinion...

    Yeah definitely not worth the time in my opinion for the maybe 2 hp yield the throttle requires. I appreciate all the input
  14. Replies
    3
    Views
    1,481

    Only thing I could think is you touched something...

    Only thing I could think is you touched something you aren?t suppose to. Don?t touch the torque tables at that mod level you?ll get yourself in more muddy water. Sounds like too much torque...
  15. Replies
    3
    Views
    1,830

    Jlt is known for needed quite a bit of work

    Jlt is known for needed quite a bit of work
  16. Replies
    6
    Views
    2,343

    your OSS maps for your base table looks like it...

    your OSS maps for your base table looks like it set to shift really short, stock the 1-2 shift is usually 1700 rpm OSS. Something to look at. Also try copying your torque modulation alt 2 table (aka...
  17. Replies
    6
    Views
    2,343

    It should lock under WOT, you may be blowing past...

    It should lock under WOT, you may be blowing past your locked limiter causing it to stay unlocked. Try raising the limiter Trans > Torque management> Torque converter > Locked torque limit, raise it...
  18. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    Also it?s a gen 1

    Also it?s a gen 1
  19. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    It?s currently using the stock throttle body....

    It?s currently using the stock throttle body. It?s not on my car, it?s in someone?s im going to tune. I told him to keep the stock throttle body because it works the best. And his rational for...
  20. Replies
    10
    Views
    2,315

    Exactly what Elliot said, or get a bigger MAF...

    Exactly what Elliot said, or get a bigger MAF housing like the pmas 120mm MAF housing which is scaled to 165 lb/min which you?ll never hit
  21. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    I appreciate it I?ll give it a look as long as...

    I appreciate it I?ll give it a look as long as it?s not throwing any errors I honestly don?t care.
  22. Replies
    2
    Views
    897

    So basically anything and everything that deals...

    So basically anything and everything that deals with custom tunes got slapped by the alphabet company and now doesn?t exist, so small business owners are screwed gotcha.
  23. Replies
    1
    Views
    1,034

    Turn off the variable cam tables. Is usually the...

    Turn off the variable cam tables. Is usually the minimum and turn the CEL off for VCT. Not cam position the motor still needs that
  24. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    I 100% agree I kept telling him just polish the...

    I 100% agree I kept telling him just polish the stock throttle but he?s not taking no for an answer. If you happen to know the values that would be great. Or PM me. I found some for the 85mm I?m sure...
  25. Thread: BBK 90mm

    by aaronson
    Replies
    10
    Views
    2,070

    BBK 90mm

    Anyone have the data for this throttle body. Person insisted on using it because it?s ?pretty? even though I told him it?s more issues than it?s worth.
Results 1 to 25 of 306
Page 1 of 13 1 2 3 4