Search:

Type: Posts; User: 88nec

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Sticky: Hello everyone. I have a jeep wj 2004 4.7 pcm...

    Hello everyone. I have a jeep wj 2004 4.7 pcm JTEC+. I turn off p0443 and p0136 p0158, the MIL lamp is off, but there are errors when reading with a scanner. What can be done about it?
  2. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    thank you for your work. Can I use these tables...

    thank you for your work. Can I use these tables without the involvement of the NN network?
  3. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    share the firmware

    share the firmware
  4. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    I used this guy's technology. it helped me a lot....

    I used this guy's technology. it helped me a lot. Thanks for the advice.
    I turned off the oxygen sensor control and the NN network.
    I share the firmware and record the log. In some loads, the...
  5. i need vin code

    i need vin code
  6. Replies
    1
    Views
    1,017

    116524 116525

    116524
    116525
  7. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    I have a stock setup. the engine runs on it very...

    I have a stock setup. the engine runs on it very richly.
    I ran into a problem while editing VE tables. When you try to decrease or add fuel, there is no reaction to the action. If the cell has gone...
  8. Replies
    9
    Views
    3,063

    Are all the pulleys native? I ran into a problem,...

    Are all the pulleys native? I ran into a problem, the profile of the stream was too sharp. On 6.2, the belt goes green after all, reinforced.
    Does the pulley clutch work exactly? Bearings in the...
  9. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    I understood you. Thank you. I tried to enrich...

    I understood you. Thank you. I tried to enrich the mixture using the AFR sensor, but reached 300% in some cells in the VE table, and realized that it was useless, nothing really changed. Problem with...
  10. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    how did you understand that there is no PE mode?...

    how did you understand that there is no PE mode? right now installed 2.9 volts on the pedal.
    Desired mix in log 10.5 afr or 0.75 lambda. The injection time is 11.6ms, but this is still not enough...
  11. Replies
    9
    Views
    3,063

    a whistling sound would be heard if the belt...

    a whistling sound would be heard if the belt slipped. If the compressor roller slips, then this can be seen from the inlet pressure. Is there a log where you can see the problem?
  12. from dodge neon 2.4 srt is. necessary?

    from dodge neon 2.4 srt is. necessary?
  13. Thread: lean mixture 5,7

    by 88nec
    Replies
    19
    Views
    3,794

    lean mixture 5,7

    under certain conditions, I get a lean mixture. I can?t understand what he?s missing. The PCM is trying to enrich the mixture. Ignition misfires appear on the 8th and 7th cylinders. I associate...
  14. Replies
    9
    Views
    3,063

    the setting is based on the output shaft sensor...

    the setting is based on the output shaft sensor and not on the wheels. therefore, the main pairs of gearboxes do not participate here as in NAG1
  15. Thread: pt cruiser

    by 88nec
    Replies
    1
    Views
    751

    this automatic transmission can only be...

    this automatic transmission can only be indirectly configured
  16. Replies
    1
    Views
    1,041

    A580 and egs52 / 53 Autostick

    The 2008 Wrangler JK was equipped with 5.7 Hemi driven NGC4 and NAG1 driven EGS52 and a shift selector from wk2.
    The problem is in the support of the autostick function. When the first gear is...
  17. Replies
    15
    Views
    3,038

    did you manage to flash it remotely via j2534 or...

    did you manage to flash it remotely via j2534 or cda?
  18. Replies
    10
    Views
    2,935

    there is a parameter whether this system is...

    there is a parameter whether this system is provided or not. and then parameter 1 shaft or not. and the fact that it is further disabled is a feature of this control unit and the operating system
  19. Thread: Help!!

    by 88nec
    Replies
    2
    Views
    778

    bypass cable required. hp tuner sell them

    bypass cable required. hp tuner sell them
  20. Replies
    5
    Views
    1,881

    how to distinguish a knock from an explosion and...

    how to distinguish a knock from an explosion and a knock from a mechanical part in an explosion system and a compressor
  21. Replies
    2,288
    Views
    1,644,364

    Sticky: Hello guys everyone. I work at a chrysler, GM,...

    Hello guys everyone. I work at a chrysler, GM, ford service station. I diagnose electronic engine control systems, automatic transmissions, abs, and other equipment in cars. I am also engaged in...
  22. Replies
    2
    Views
    925

    I'm asking))). Why then is the maximum engine...

    I'm asking))). Why then is the maximum engine torque not shown? 680 newtons.
  23. Replies
    2
    Views
    925

    Actual Torque SRT 6.4

    It is not possible to raise the torque above 600 Newtons. I attach two logs. PCM GPEC2A
    108698
    108699
    108700
  24. Replies
    6
    Views
    1,762

    Nevertheless, I do not recommend lowering...

    Nevertheless, I do not recommend lowering temperatures. The most extreme is low 95, medium 97, high 99.
    Why is nothing done in the program to work without catalysts?
  25. Replies
    6
    Views
    1,762

    106392 leveled the speed of the automatic...

    106392

    leveled the speed of the automatic transmission after 80%. from your data. Also for the test
Results 1 to 25 of 45
Page 1 of 2 1 2