Downloaded a newer { think it was 3.7 } version and boom, it works???
Type: Posts; User: SilverZ06
Downloaded a newer { think it was 3.7 } version and boom, it works???
I just upgraded my laptop running windows 7 with a SSD hard drive and more Ram, tried to connect and got the "VCM Editor has encountered a problem...object inference not set to an interface of an...
So I plugged into a work van we have 2006 duramax and the scan does not show 80% of info
Shows TPS at 100% my buddy says maybe my scanner will not do Duramax?
The reason I scanned it was because it...
I am impressed! I was going to mention that I finally figured out how you got into my shop through that prison work release program. I hired you to sweep up not take all these pictures, now get back...
Hey that's my shop, Your that guy who was in here earlier with the camera asking all those tuning questions.
Hi guys I put a 2004 5.3 motor in a 97 S10, I also put a 4L60 from a 2002 Sierra in behind. I used a harness and ecu from a 2002 Sierra as well. I have speed reading, performed a tcc lock up in gear,...
Can you please explain how to set filter?
Thanks.
1.] Turn key on, but don't start engine.
2.] Connect to scanner.
3.] Start scanning...my wide band starts reading 13-14-15 anywhere in that range? But engine has not even started?
Is this...
Well Thanks guys, looks like it all fixed I set the Open loop EQ ratio table to 1.00 that did the trick.
I also checked for vacuum leaks...none.
Set the top 3 DTC for the Maf to first error.
Fixed...
Now that looks normal, thanks Chuck. I will clean mine up tomorrow afternoon and report back.
Thanks Chuck, much appreciated.
I will inquire about the Map sensor.
No boost yet, going to drop a turbo in the spring, so I figured just go with the 3 bar for now...I down think it will negatively effect anything just more cells in certain areas.
Map is stock one...
Thanks a ton for looking at these issue, I will make these changes tomorrow afternoon when I get home from work. The tune is all stock from a 2004 express van. I have compared my tune against other...
I'm not sure, mine does that sometimes on the compare?
The cam is a called a triple 12 I will post specs shortly.
but her is log...cold start and 15 - 20 seconds barely able to idle.....the you can see have way thru this log....bam! nice idle.
No knock...
I noticed that knock, I tried playing with the spark in that area and smooth it out a little, but when I flashed it and started it... it ran like crap on startup so I went back to the tune I posted....
i'm pretty new at this, so I'm just double checking with your instruction, that all. will un-checking them send it into SD mode quicker? and maybe help the idle issue?
Thanks for your help. OK I set...
Un-check them?
Here is a quick log of the start up problem. you can see very low RPM for a few seconds until it catches its breath and gets up to 700+,
Is it spark? Fuel? Air?
Here is tune, I will try to log issue today.
One
I had a quick look at your tune...your PE is coming in at 5500 RPM you might want to try bringing it in earlier, I have been told 3-3500
I have a 5.3 in a s10 running a base tune from the 2004 5.3....
I have a small cam, adjusted taget idle and airflow up a bit.
I am Running no Maf just STFT with no LTFT, I performed all VE error tuning. Thats all good.
When I fire this 5.3 it idles very low and...
Ok so what is my issue? Why is truck pulling away at 700 RPM like it has no converter slippage?
I've had automatics all my life and never had this that bad? Is it possible I just have a tight...
So why is it wired to your brake switch?
Good day all, I swapped a 5.3 / 4L60 trans into a S10
Have idle down to 710-720. But I can still feel it pulling, just touching the gas
results in instant forward motion, not slippage is detected?...