Search:

Type: Posts; User: Russ K

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    136

    This is a stock tune from a 2005 Silverado 2500...

    This is a stock tune from a 2005 Silverado 2500 6L with 4.10 gears.

    Russ Kemp
  2. Hi luciddeath, tried raising the torque delta...

    Hi luciddeath, tried raising the torque delta tables. No difference in the the timing, still dropping to -8.7*

    Russ Kemp
  3. Did you try setting the ISS to 36? Russ Kemp

    Did you try setting the ISS to 36?

    Russ Kemp
  4. Replies
    2
    Views
    171

    Your WOT downshift speeds are higher than the...

    Your WOT downshift speeds are higher than the upshift speeds.

    Russ Kemp
  5. Is the speedo accurate? I get 31,470 pulses/mile....

    Is the speedo accurate? I get 31,470 pulses/mile. Also try logging the trans output rpm. To calculate the trans mile per hour, do this; (trans output shaft rpm*60)/trans output revs per mile. The...
  6. Replies
    2
    Views
    201

    Change the whole TCC lockup rate after upshift...

    Change the whole TCC lockup rate after upshift table to 650 ft-lbs,

    Russ Kemp
  7. The vehicle will be in open loop, not damaging...

    The vehicle will be in open loop, not damaging the O2 sensors.

    Russ Kemp
  8. Did you try disabling the Cat test & Cat Mil in...

    Did you try disabling the Cat test & Cat Mil in Engine Diagnostics > Exhaust?

    Russ Kemp
  9. Raise your O2 Readiness ECT. Russ Kemp

    Raise your O2 Readiness ECT.

    Russ Kemp
  10. Replies
    26
    Views
    1,256

    I would really think about going with the BTR...

    I would really think about going with the BTR Stage 2 cam, the Stage 3 will loose torque vs the 2 on the low end.

    Russ Kemp
  11. Replies
    4
    Views
    157

    Just solved the same issue with a 1976 Sierra...

    Just solved the same issue with a 1976 Sierra with a 5.3/4L60E with the OEM manual transfer case. Had a speed signal generator inline with the speedo cable. First got the scanner speed to match a...
  12. Replies
    23
    Views
    790

    The Comp 268 cam with a 113 LSA has a -8* overlap...

    The Comp 268 cam with a 113 LSA has a -8* overlap @ .050 and will idle very smooth.

    Russ Kemp
  13. Replies
    8
    Views
    346

    Then modify the TPS sensor to make it adjustable....

    Then modify the TPS sensor to make it adjustable.



    I never disable the adaptive idle when tuning. The Base Running Airflow is the base position of the IAC before any adaptives.



    The...
  14. Replies
    8
    Views
    346

    You need to adjust the throttle stop screw to get...

    You need to adjust the throttle stop screw to get the IAC to 20-40 at hot idle in park. The Base Running Airflow doesn't affect the IAC counts.

    Russ Kemp
  15. Replies
    4
    Views
    225

    Look at the STFT's, they are not 0. Russ Kemp

    Look at the STFT's, they are not 0.

    Russ Kemp
  16. Replies
    4
    Views
    225

    You're in closed loop. Disable CL by maxing the...

    You're in closed loop. Disable CL by maxing the O2 readiness ECT table.

    Russ Kemp
  17. Replies
    7
    Views
    328

    That's because the Corvette has a trans axle. And...

    That's because the Corvette has a trans axle. And you can't change it in the tune, so you will need to have the PCM flashed with a compatible tune from a F Body or Truck.

    A segment swap would work...
  18. You have the WOT 1-2 set at 9190 RPM, the 2-3 is...

    You have the WOT 1-2 set at 9190 RPM, the 2-3 is set to 8595 RPM and the 3-4 is set to 7332 RPM. Your PT 2-3 shift is set to 8376 RPM, the PT 3-4 shift is set to 7120.

    The Dodge shift speed tables...
  19. 2010 Challenger 5.7 A5 low WOT spark timing

    For some reason, the WOT spark timing is much lower than the WOT Base spark table. As you can see, I also set the WOT Thermal spark table and the VVT MBT tables to match the WOT Base spark table....
  20. Replies
    20
    Views
    791

    If the car was actually going so lean that the...

    If the car was actually going so lean that the wide band maxed out, the car would be hesitating/bucking badly. Log the front O2 MV, if it drops below ~ 200 MV, then you are truly lean. But I think...
  21. Look at the Electronic Throttle > Throttle Area...

    Look at the Electronic Throttle > Throttle Area Limits > Max % vs RPM. It's limiting the throttle to 37% until 2400 RPM. Also raise the Max Torque > Peak Torque.

    Russ Kemp
  22. Actually, you get a 75% (rounded down) trade in...

    Actually, you get a 75% (rounded down) trade in towards a model year license. So it takes more than 6 credits for a model year if you're just licensing one vehicle at a time.

    Russ Kemp
  23. Replies
    7
    Views
    293

    I can't open your tune, a dialog box says...

    I can't open your tune, a dialog box says "Translating Tune unknown source" But besides the Map dropping at WOT, your Bank 1 O2 MV is dropping. Looks like there is a misfire on Bank 1.

    Russ Kemp
  24. Replies
    3
    Views
    386

    The throttle is closing at 3900 RPM. Disable the...

    The throttle is closing at 3900 RPM. Disable the ETC limit in the Cutoff, DFCO tab.

    Russ Kemp
  25. Replies
    29
    Views
    7,026

    The 2008 Sierra that I replied to does. You need...

    The 2008 Sierra that I replied to does. You need to set all DoD codes to no error reported, uncheck the SES box, and change the DoD to disabled.

    Russ Kemp
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4