Search:

Type: Posts; User: IARLLC

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. A reduction in knock retard right when you hit...

    A reduction in knock retard right when you hit the gas, due to getting the right amount of gas right when you hit it, is quite noticeable. On older V6 P04, tuning VE had questionable value because it...
  2. Simply put, when you hit the gas the MAF won't...

    Simply put, when you hit the gas the MAF won't even find out it happened for a while. The MAF is down around the corner. However, the MAP is right there in the manifold and it knows the very moment...
  3. Replies
    3
    Views
    150

    Thanks for letting us know! Really appreciated!

    Thanks for letting us know! Really appreciated!
  4. Replies
    9
    Views
    143

    The two sides are different. One side is a type...

    The two sides are different. One side is a type of ball and socket while the other side uses a type of rolled metal ring to seal...if I remember right...
  5. Replies
    2
    Views
    57

    NO BCM control. I have been begging for years. ...

    NO BCM control. I have been begging for years.

    Which GEN? With GEN5 PCM gets BCM speed limit via GMLAN. If you don't want the BCM's opinion, just go to Speedo>Limiter>General>Source>GMLAN and...
  6. Thread: Lean tip in

    by IARLLC
    Replies
    15
    Views
    364

    You really need the VVE right on in order to make...

    You really need the VVE right on in order to make accurate transitions. The MAP finds out that you opened the door (throttle) WAY sooner than the MAF. And a colder motor is much more likely to...
  7. My old 68 C10 weighed 3660, not too portly by...

    My old 68 C10 weighed 3660, not too portly by today's standards.

    T56 is on his list.

    1/16" off the heads is a lot. Small base circle cam probably...maybe stock length pushrods are not too far...
  8. Replies
    6
    Views
    142

    Nope

    Nope
  9. Adjusting part throttle shifts is more art than...

    Adjusting part throttle shifts is more art than science...as lots of cars take one setting into more consideration than another. I raise them a little at a time together and see how it goes.

    The...
  10. Replies
    25
    Views
    397

    Cool for me too. I found out that I don't have to...

    Cool for me too. I found out that I don't have to pay ACDelcoTDS every time:)
  11. Something like this:...

    Something like this:
    https://forum.hptuners.com/showthread.php?10993-OMG-why-does-my-TPS-only-read-88-at-WOT
    https://forum.hptuners.com/showthread.php?4961-2005-A4-GTO-Help-please&p=32069#post32069
  12. Replies
    25
    Views
    397

    That is AWESOME! Glad you did not give up. Good...

    That is AWESOME! Glad you did not give up. Good job!
  13. Replies
    25
    Views
    397

    Recently I used a 2002 Corvette 0411 (obviously...

    Recently I used a 2002 Corvette 0411 (obviously V8:) on a friend's Mini 4.3 swap. It worked flawlessly. I just used GM tools with ACDelcoTDS to change the system to a manual trans 2002 4.3 5speed....
  14. Replies
    25
    Views
    397

    You are right. Even a fresh 2019 L86 runs...

    You are right. Even a fresh 2019 L86 runs noticeably smoother after the crank position is learned. It is worth it to find a 2003 V8 P59. I don't know all of the differences between 2002 and 2003 but...
  15. Replies
    3
    Views
    128

    Yep. 232/241 at .050? That cam will be much less...

    Yep. 232/241 at .050? That cam will be much less efficient (pump less air) below 3500-4000rpm than a stock cam....but if you don't mind the trade-off and need something that makes a lot more power at...
  16. Replies
    25
    Views
    397

    There is certainly no need to go from an 03 back...

    There is certainly no need to go from an 03 back to an 02. The 03 has a few advantages and yes, the 03 P59 is for both V6 and V8. My Tahoe has a P59. I am just not totally sure that a segment swap...
  17. Replies
    25
    Views
    397

    OK. Yeah, I am not totally sure how well segment...

    OK. Yeah, I am not totally sure how well segment swaps switch everything over. I would tend to think that it needs to be flashed to a V8 OS in order to be sure everything lands right....like injector...
  18. Replies
    25
    Views
    397

    Are there any other codes present? A code would...

    Are there any other codes present? A code would keep it from learning the position. I understand that your system says it completes the test but...it seems possible that it is wrong.

    I cannot...
  19. Replies
    6
    Views
    137

    Thanks for letting me know. One of these guys...

    Thanks for letting me know. One of these guys bought an M600 for his 2009 Y61 and wants me to set it up from scratch. I'd much rather tune it with HPTuners but...
  20. Replies
    6
    Views
    137

    Hi jarrah. Are all of these Patrol TB48 2017+? I...

    Hi jarrah.
    Are all of these Patrol TB48 2017+? I have been waiting forever to be able to tune a group of 2009 Y61. Do you know if they can be tuned? The vehicle list just shows 2017+
  21. Replies
    25
    Views
    397

    Another criteria, if the engine does not smooth...

    Another criteria, if the engine does not smooth out enough before the test, it usually won't run. The Tech2 will say so if that is the case.
  22. Replies
    6
    Views
    293

    Yes. It did not go up until 2017.

    Yes. It did not go up until 2017.
  23. Yep. What mbray01 said. If the two fans are...

    Yep. What mbray01 said.

    If the two fans are together in the shroud (not separated by any kind of wall between them) the first fan will just pull air through the other fan hole....not much through...
  24. Replies
    25
    Views
    397

    OK. Cool. Must all be in order. I am not sure...

    OK. Cool. Must all be in order.

    I am not sure on doing the learn with HPTuners. I have read a lot of people describing the process on HPTuners where the rpm does not cut off.

    With a Tech2 it...
  25. Replies
    25
    Views
    397

    P59 does not have DOD, so no need to consider...

    P59 does not have DOD, so no need to consider that.

    This seems like an issue of cam signal at the wrong time. This might also explain the wrong injector shutting down when you were running those...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4