Search:

Type: Posts; User: momotunes

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    792

    Well I tried a different computer with a fresh...

    Well I tried a different computer with a fresh install and the scanner hooks up with no issues now. So weird. It still was failing midwrite but this time would fail at 96 percent vs like 27-55...
  2. I don't agree with injecting fuel with the intake...

    I don't agree with injecting fuel with the intake valve open/after the exhaust valve closes. Do as OEM intended and spray on the back of a closed valve. The temporary gain in idle stability isn't...
  3. Thank you veefour! I'll do more some more...

    Thank you veefour! I'll do more some more adjusting on this. Glad to know Ford went back to MAP. I figured they were going down the route of inferring the whole darn engine lol. Speaking of...
  4. Bump. Anybody have any information? Cylair...

    Bump.

    Anybody have any information?

    Cylair Filter: When enabled (and Anticipation Logic is disabled) a filtered value of MAF airmass is used by the PCM. When disabled the current calculated...
  5. Seeking Clarifications on Switches/Tables - 3V Motors

    Probably too many questions for one post. I figured it would be better to post them in one vs flooding the forum.

    I'm seeking clarification on the following switches.

    MAF Adaption:...
  6. Replies
    17
    Views
    792

    Same issues with mine. Mine seemed to act up...

    Same issues with mine. Mine seemed to act up whenever I updated the firmware. Tried another cable with no luck. I tried a bench harness on my E38 and same result. Ford truck fails midwrite...
  7. Replies
    12
    Views
    507

    I had a similar issue with my 04. Bank one was...

    I had a similar issue with my 04. Bank one was adding a ton of fuel and bank two was pulling. My wideband was installed on bank one. As the revs went up they came pretty close. At idle wideband...
  8. Replies
    2
    Views
    216

    I don't think windows RT will work. I believe RT...

    I don't think windows RT will work. I believe RT will only install programs from the Microsoft store app. Every laptop I've seen with Windows 10 s let's you upgrade to regular windows for free. ...
  9. Replies
    1
    Views
    115

    Knock Retard Valid Max

    Question.. I'm confused on this parameter. I'm having a hard time understanding the description. What exactly does the Knock Retard valid max do?

    Thanks everyone.


    92473
  10. Replies
    37
    Views
    1,035

    Is it possible different ECU handle the MAF data...

    Is it possible different ECU handle the MAF data differently? On mine, messing with the MAF to correct fueling (with correct injector data) just messed with drivability. Wheel torque error was...
  11. Replies
    8
    Views
    647

    Mines failing mid write on a F150. Won't detect...

    Mines failing mid write on a F150. Won't detect my mustang, and giving me issues connecting to my Silverado. HP suggested a bench harness. Doing the same thing. I updated the device firmware and...
  12. Replies
    6
    Views
    359

    92238 For virtual set this table flat across...

    92238

    For virtual set this table flat across and see if fuel trims improve.
  13. Replies
    6
    Views
    311

    When did they say they were going to remove...

    When did they say they were going to remove switchs??
  14. I believe just the exhaust temp table. If memory...

    I believe just the exhaust temp table. If memory serves me correctly it good by RPM and load.
  15. Hello. I got the small case.

    Hello. I got the small case.
  16. Replies
    6
    Views
    359

    Did your ethanol percentage go back up? I've...

    Did your ethanol percentage go back up? I've seen a lot of the flex sensors go bad and cause this exact issue. Disable flex, reset trims, and log to confirm.
  17. Replies
    3
    Views
    507

    You're correct. I'm sorry about the confusion.

    You're correct. I'm sorry about the confusion.
  18. Replies
    4
    Views
    272

    Thank you. This is an 04 as well. I'm going to...

    Thank you. This is an 04 as well. I'm going to try it. On a side note I remember now, when I made the axis the same it would throw a second and fourth gear incorrect ratio fault code and the...
  19. Replies
    73
    Views
    8,662

    Correct

    Correct
  20. Replies
    4
    Views
    272

    Sorry, overlap was a poor way to explain. What...

    Sorry, overlap was a poor way to explain. What happens is I run into issues where the torque converter locks and unlocks over and over. Of course in certain ranges I adjusted incorrectly. Same...
  21. Hahahaha that's a lot of posts you've read. You...

    Hahahaha that's a lot of posts you've read. You know I get mixed answers too or at least that's how I read them. Anyways I'm not sure on your engine but I'll explain what I did on my N/A built 5.4...
  22. I bought this from Amazon and it fit the device...

    I bought this from Amazon and it fit the device like it was made for it. Carrying Case for GoPro Hero 7 Black,6,5, 4, Black, Silver, 3+, 3,Hero(2018) and Accessories,HSU Protective Security Bag,...
  23. Replies
    17
    Views
    496

    Be easy on it until you get your wideband. Also,...

    Be easy on it until you get your wideband. Also, probably try putting MAF back to stock once you do install wideband and just keep working on slopes & minimum pulse width.
  24. Replies
    5
    Views
    322

    Be careful doing this. I know it helps in some...

    Be careful doing this. I know it helps in some areas to spray fuel after the exhaust valve closes with overlap but it can easily lead to cylinder washing. I use to do this too. When I changed my...
  25. Replies
    17
    Views
    496

    Increase slopes to decrease amount of fuel and...

    Increase slopes to decrease amount of fuel and decrease slopes to inject more fuel. Try lowering minimum pulse a tad too if you have too.

    Are you sure injectors are the issue? Did you try...
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4