Search:

Type: Posts; User: orange ss

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. 2 ecms, 2 separate issues apparently...i couldn't...

    2 ecms, 2 separate issues apparently...i couldn't connect to my buddy's spare ecm for some reason. The original issue was resolved with pin reposition.
  2. ECM, I assumed those pins were hard mounted to a...

    ECM, I assumed those pins were hard mounted to a board, apparently not
  3. recessed pin (C2,19) in the PCM not making...

    recessed pin (C2,19) in the PCM not making contact with connector, explains why I couldn't communicate in the vehicle or on the bench. I pulled the pin back out with needle nose pliers, everything...
  4. MPVI1, I did contact support, first response was...

    MPVI1, I did contact support, first response was electrical interference (noise), suggested using bench harness ( already tried that), second response was to download beta version...I tuned a Gen III...
  5. Unable to connect to vehicle diagnostic protocol.

    received error message trying to connect to vehicle with LS1 swap. Harness is new aftermarket, all circuits valid/operational. Tried 2 different pcm's in vehicle and on bench harness with same...
  6. I believe there is an option for PRNDL ( trans...

    I believe there is an option for PRNDL ( trans section?), None or P/N switch for that PCM...use a micro switch to switch ground ( I believe P is ground)
  7. need to do a system segment swap to utilize the...

    need to do a system segment swap to utilize the a/c pressure transducer function
  8. plenty of 5vdc circuits from the pcm...TPS, EGR,...

    plenty of 5vdc circuits from the pcm...TPS, EGR, A/C, etc and even some that are not used..tap into one of them
  9. Replies
    5
    Views
    413

    good find, thanks for following up

    good find, thanks for following up
  10. Replies
    5
    Views
    413

    pin 58 is serial data, looks like wiring is...

    pin 58 is serial data, looks like wiring is correct
  11. Replies
    17
    Views
    1,187

    same issue with Windows 10

    same issue with Windows 10
  12. Replies
    29
    Views
    6,047

    no ticket, some parameters not recording during...

    no ticket, some parameters not recording during stand alone data logging....problem is well known, recommended fix was to use the Beta version until the problem got resolved.
  13. Replies
    29
    Views
    6,047

    Stand alone data logging bug fixed?

    Stand alone data logging bug fixed?
  14. Thread: log files !

    by orange ss
    Replies
    4
    Views
    577

    had same issue, was told by support to download...

    had same issue, was told by support to download Beta version, stand alone works now
  15. Replies
    4
    Views
    372

    Fan Frictional Airflow table (or similar, cant...

    Fan Frictional Airflow table (or similar, cant remember exact terminology)
  16. Replies
    3
    Views
    529

    Did you raise your a/c compressor cutout RPM...

    Did you raise your a/c compressor cutout RPM limit?
  17. Did you perform CASE relearn after swapping crank...

    Did you perform CASE relearn after swapping crank sensor?
  18. replace distributor cap

    replace distributor cap
  19. Thread: Aem 30-0310

    by orange ss
    Replies
    3
    Views
    646

    Thank you, but the question was more targeted to...

    Thank you, but the question was more targeted to the accuracy of the default settings. I didn't have my laptop with me so I couldn't confirm. I just checked the formula and it is correct. Thanks...
  20. Thread: Aem 30-0310

    by orange ss
    Replies
    3
    Views
    646

    Aem 30-0310

    Friend has an AEM 03-310 wideband that I will be using to tune his car. HPTuners has a default option for this wideband, the range is 8-18 AFR ( I tune using lambda) but according to AEM...
  21. Replies
    1
    Views
    321

    does your efan conversion include PCM control of...

    does your efan conversion include PCM control of AC fans?
  22. Replies
    2
    Views
    385

    still looking?

    still looking?
  23. Replies
    98
    Views
    22,068

    ouch!

    ouch!
  24. Thread: Layouts?

    by orange ss
    Replies
    0
    Views
    718

    Layouts?

    Is there a Layout repository here somewhere? I don't know why but all the Layouts I had saved have the same parameters now (channels, graphs etc.) Or does anyone know why this happened?
  25. Replies
    98
    Views
    22,068

    do you have the IAT in the intake manifold or an...

    do you have the IAT in the intake manifold or an intake tube?
Results 1 to 25 of 241
Page 1 of 10 1 2 3 4