So... I found, and read this;
Trans Cleaning Procedure:
Begin the transmission cleaning procedure. Before starting the procedure, you must log the PID "Cleaning Status" in the scanner to be...
Type: Posts; User: 1364838952
So... I found, and read this;
Trans Cleaning Procedure:
Begin the transmission cleaning procedure. Before starting the procedure, you must log the PID "Cleaning Status" in the scanner to be...
You have broken the input sprag. Welcome to the world of 4L60E's.. Get used to pulling, repairing, and re-installing as it is going to be a routine you will become familiar with..
Your list does...
Notorious-as Plohr alludes to, sometimes, on some vehicles you simply CANNOT do a QUICK/FAST learn. Just like you are describing, it will indicate "Temp Lo" regardless of the temperature, and then...
Okay.. I got the dash trans temp situation resolved. That was on another vehicle I was working on. I had to license the vehicle and burn the correct operating system back into the vehicle. Once I got...
So, original pack was 24240651.. The replacement pack has 24275871 on it... I HOPE that I'm able to get this flashed at a GM dealer and have it work.. Otherwise, I just wasted a bunch of $ and I'll...
I've got an O7 Escalade W/6l80e trans in it that we are working on. Came in with shift solenoid codes and blown up torque converter. We have seen this a lot where the blown up torque converter plugs...
You would be better served by re-gearing the vehicle. You *could* change all of the normal shift tables to a significantly higher MPH so that the trans will not upshift until you hit those speeds....
2015 Chevrolet Silverado 2 wheel drive. Transmission is rebuilt, and all clearances on ALL clutch packs checked and corrected and all are within ATSG specs. New torque converter, Trans-go shift kit,...
For those of you following this post.. I got help from RUSS KEMP (The FREAKIN' DREAM TEAM OF TUNING!) and he told me to try deleting VATS. Welp.. I deleted VATS and SUCCESS!!!!!! Everything works now...
Okay.. That did not work.. The engine would not even start with his engine data copied over. No fire condition, or no fuel pump power... Burned a previous tune with new OS and 80E segment swap with...
So, in doing research it appears that other people have done this in a similar fashion. So far I've done a WRITE ENTIRE to put the 12592618 OS onto the customers PCM. Then went back and did a WRITE...
The relay method is... Not desirable? I'm sure this can be done so that all diagnostics perform correctly. I like elegant solutions that are as close to factory in appearance & function as...
Im in the same boat here.. What did you end up doing to get the segment swap to work???? Please share with us!
Okay.. I talked to my customer and this is what he said.. When his tuner attempted the segment swap the engine would no longer rev if you spiked the throttle. It would go into reduced power mode....
Plugged filter, bad torque converter (most likely), or damaged pump from improper trans installation (torque converter not seated). I'd go in this order for most likely culprit;
1. Bad Converter
2....
I know you swapped this engine & trans into your vehicle... What about the wiring harness? Do you have BOTH speed sensors on the 80E connected and working? Can you log the input, or turbine, speed...
That is an ADDER or offset table designed to bring torque UP to prevent slipping at low rpm load (as per hp tuners description).
Prior to this I was only interested in doing the segment swap.. Now...
Okay.. I'm reviewing the new tune compared to the old one and I think I see a potential issue. If you click on the OS tab, you will see that the new tune is using an updated SPEED DENSITY tune, or...
The first tune is the ORIGINAL tune and OS that was on the truck when it came in. The 2nd tune is the new OS, and Segment swap, that I burned in.
Like the title says.. Truck is an 05 Silverado. Came in to my shop with OS12619624. Cust has installed a 4L80E trans that we built and sold him as a carry out unit. His tuner could not perform the...
Was this vehicle originally equipped with a 4L60E? If so, did you re-pin the white wire, or otherwise move the TCC PWM wire over to where the white wire was previously in the trans connector? Or, are...
Like the title says... I think my interface took a shit today. I used it several days ago and it was glitchy.. It did not want to connect. If I kept trying it would finally connect to VCM scanner....
I have taken a video with my phone that I will upload when I get home. The logs that are recorded above are not showing what is happening with the FT's while actually recording. The only thing you...
Having an issue where the VCM scanner will bounce back & forth between 0-9% on BOTH of the LTFT graphs-even with the engine OFF. If I attempt to log fueling, it consistently shows 5% error...
This is a SPEED DENSITY tune. Your MAF is disabled. What is a HOT AIR intake? VE table could use a little smoothing. Look at the 3D Graph of the table.. Stock cam? I ask because the RAF appears to...