Search:

Type: Posts; User: Mopwer

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    2,708

    Turned out being bad O2 sensors. My wideband was...

    Turned out being bad O2 sensors. My wideband was showing super lean when the narrow band was showing rich. Installed new O2 sensors and a new MAP (was cheap) and runs no issue. And my wideband...
  2. Replies
    16
    Views
    2,708

    I haven't been able to figure out testing the TB...

    I haven't been able to figure out testing the TB yet, but did find that my PCV hoses was collapsing under the vacuum. Replaced the heater hose that was on there with stiffer wall hose and fixed...
  3. Replies
    16
    Views
    2,708

    Thanks for the input, McCloud. I originally was...

    Thanks for the input, McCloud. I originally was thinking it could be a cracked intake, but couldn't find anything obvious. Might remove it to take a closer look.

    I'll throw a meter on the TB and...
  4. Replies
    16
    Views
    2,708

    I just did another log with the trans in park and...

    I just did another log with the trans in park and just bringing up the revs and holding it, trying to get it to act up. Engine wasn't warm yet, but I did notice that the throttle pedal voltage...
  5. Replies
    16
    Views
    2,708

    Just looked up PHI and believe it relates to the...

    Just looked up PHI and believe it relates to the narrow band settings. I've attached the original file from the PCM as I received it from HotWire.

    I had a tuner tune the truck (has a 6.4 cam...
  6. Replies
    16
    Views
    2,708

    Sorry, just started acting up as far as the...

    Sorry, just started acting up as far as the engine missing at part throttle. I don't recall if the accelerator pedal has always had that output or not. Just started looking at it due to the...
  7. Replies
    16
    Views
    2,708

    Yes it does show NGC4. 111084

    Yes it does show NGC4.

    111084
  8. Replies
    16
    Views
    2,708

    Application for the pedal (68043161AD) fits 2009...

    Application for the pedal (68043161AD) fits 2009 to current Rams. PCM is a 2009 Jeep GC 5.7.
  9. Replies
    16
    Views
    2,708

    Here is a log of with the previous pedal. You...

    Here is a log of with the previous pedal. You can see how it isn't consistent. I don't see anything else that jumps out having the potential for causing the miss/stumble.

    111029
  10. Replies
    16
    Views
    2,708

    Inconsistent Throttle Pedal Output

    Hello.

    I have a 78 Dodge truck with a 2010 LX 5.7 hemi swapped in. Throttle body came with the engine but not the pedal. I'm using one from a Ram I believe. Had originally bought the pedal from...
  11. Replies
    15
    Views
    3,885

    Thanks for the info, Acln99. Are the Ram PCMs...

    Thanks for the info, Acln99. Are the Ram PCMs the same way? Were you using a stock harness? I'm using a Hotwire Auto harness and no mention of the need for the wireless ignition module from them...
  12. Replies
    15
    Views
    3,885

    No response from Hotwire Auto on the PCM changes...

    No response from Hotwire Auto on the PCM changes that are needed ro run on this harness. Probably won't get one. Any ideas? I noticed an option for Start over CAN Bus? My harness is getting a 12v...
  13. Replies
    15
    Views
    3,885

    I emailed Chris at Hot Wire Auto. He sent me the...

    I emailed Chris at Hot Wire Auto. He sent me the pin outs for the coolant temp sensor and throttle pedal as I was getting High/low out of range CEL codes for those and there should be nothing wrong...
  14. Replies
    1
    Views
    1,814

    I think this is what you are looking for,...

    I think this is what you are looking for, Gonzalo. All of the plugs are in there, but you are looking for the Data Link Connector and Module-Powertrain Control C1 (black plug):
    ...
  15. Replies
    15
    Views
    3,885

    Hello, Kmoney. When I primed the oil system, I...

    Hello, Kmoney.

    When I primed the oil system, I just connected 12 volts to the solenoid on the starter and it cranked. I can also ground the start relay on the harness and it will crank.
    ...
  16. Replies
    15
    Views
    3,885

    I only hooked power up to the starter solenoid to...

    I only hooked power up to the starter solenoid to prime the oil pump. That is the only cranking I've got out of it.

    Thanks,
    Greg
  17. Replies
    15
    Views
    3,885

    Just used Write Calibration and no dice. Still...

    Just used Write Calibration and no dice. Still no crank.

    Thanks,
    Greg
  18. Replies
    15
    Views
    3,885

    Thanks for the reply, Boostjunky. I had that...

    Thanks for the reply, Boostjunky. I had that switched off before sending the PCM off for SKIM removal and never changed it back. I'll give it a shot. When I send the updated file do I choose the...
  19. Replies
    15
    Views
    3,885

    78 D100 5.7 Hemi Swap No Crank Issue

    Hello, gurus.

    Swapped a 2010 LX 5.7 hemi (6.4 manual trans cam) with a 2006 545RFE from a Ram. Using a 2011 Ram 5.7 PCM and a Hotwire Auto harness. Got it all wired up and I'm getting a no crank...
  20. Replies
    5
    Views
    4,984

    Thanks, ELaw. I would think that it could be...

    Thanks, ELaw. I would think that it could be modified through the channels.
  21. Replies
    5
    Views
    4,984

    So, if I understand correctly, I couldn't feed in...

    So, if I understand correctly, I couldn't feed in wideband info through the narrow band wiring for logging/tuning?

    Thanks,
    Greg
  22. Replies
    5
    Views
    4,984

    Narrowband to wideband

    Hello,

    Long time lurker, first time poster.

    Just purchased the MPVI 2 to tune the 2009 5.7 Hemi/545RFE going into my 1978 Dodge stepside shortbox.

    Question:

    Can the narrowband O2 sensors...
Results 1 to 22 of 22