I can understand wanting to develop the one that would be less time consuming.
Is there a reason you couldn't support both platforms?
I would be willing to place a deposit or even pay for a...
Type: Posts; User: Cheatin_Chad
I can understand wanting to develop the one that would be less time consuming.
Is there a reason you couldn't support both platforms?
I would be willing to place a deposit or even pay for a...
PalmOS
I use a Tungsten T5
How many of you guys currently own PDA's? I am interested in using this NOW. Not when I "maybe" buy a PDA in the future.
The Palm OS is currently used for the NX Maximizer made by FJO racing.
I would REALLY like to be able to use this with my Palm. I believe my T5 would be more than capable.
PC: 2.8 ghz P4/1gb
Laptop Panasonic Toughbook:366 p3/256mb
Palm Tungsten T5 w/1GB SD card
Is there any chance HPtuners would be able to run on the Palm OS in the future?
That's fantastic. Please make it Palm OS compatible. I use a Pam PDA to control my NX maximizer and FJO wideband set-up.It'd be nice to get the laptop out of the car entirely
Wow! That was fast. I paid for the update and literally minutes later I have it ready to run.This all happened in the middle of the night to top it off.
*THAT* is some great customer service.
I...
Thank you for the very prompt reply! The payment has been sent.
I never received an email. I think my e-mail server might have filtered you out.
Could you please send me the information as a PM on this board?
Just to verify, I needed software for an 04...
I need to add another vehicle this week. Is there anyway if I order it on 12/14 I can get it same or next day?
I will e-mail as well.
thank you
Paid on the 7th sending mine in on the 15th.
Thanks
Thank you I just wanted to be certain I woudln't have problems.
I checked out the software update and I am very happy with the changes made thus far.
I have also helped sell HPtuners to two...
Can anyone VERIFY with certainty which Wideband units will work?
I am interested in using either the Innovate LM1 or the FJO Racing wideband.
What needs to be done to swap a '98 from A4 to M6?
In the Force motor table my 100 Column is "0"
the 0 column is 1069 from top to bottom
My max line pressure constant is 90 I believe. I have not modified this value.
Should I make changes under...
Under TCC DC vs Line Pressure vs Trans Temp mine is 96 across the board. I should set these all to 100?
Just to clarify : What do you mean by "offset"?
Well this is even worse now.
I am slipping up to 450rpm when on the spray.
I think I am going to put the TM back to near stock to prevent banging against the limiter. Then I'll get a shift kit....
I see the IFR table goes from 0vac to 80vac in Kpa
Is 0 the value for 0 vacuum?
Would someone mind explaining this table to me as I am not sure I fully understand it.
Normally you will have...
Thanks for the update.
I like the coloring and smoothing. I haven't been able to mess with much else at this point.
Great news.
Thanks Keith.
That'd be nice. I like new stuff :)
I'd imagine because the vehicle should be able to tolerate more timing in 1st gear than 2nd ,and more in 2nd than in 3rd etc. because the engine will be seeing lower load due to the mechanical...
By full pressure do you mean adjusting the field prepopulated with Max lin pressure which is "90"?
I have not adjusted that but I am starting to move my Base shift pressures vs. Torque vs. Gear up...
I'm going to work on the VE changes this weekend.
I'd be very happy if it turned out there was something along the lines a "pump_shot" buried in the VCM that we could access.
I appreciate you guys suggestions but I really can't say I know enough...