Search:

Type: Posts; User: 4wheelinls1

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. This should start and run, all you need to do is...

    This should start and run, all you need to do is pull 15-20% out of the VE table around idle 0-1400 RPM up to 80 kpa. Popping suggests a more serious issue, are the coils wired correctly? Do you...
  2. Log the pump duty, its a closed loop system so if...

    Log the pump duty, its a closed loop system so if the duty is 100% its max, the DC tables are a feed forward. You get more from being boost referenced provided the pump can deliver at higher...
  3. I always use the LTFT + STFT for dialing in the...

    I always use the LTFT + STFT for dialing in the closed loop settings as ultimately they are the sensors the car will be running off. you can ditch the LTFT but its nice to have if the trims are a...
  4. Replies
    3
    Views
    9,066

    I wrote a Book for Tuning Aus Ford when at VCM...

    I wrote a Book for Tuning Aus Ford when at VCM Suite, contact them and see if they will give you a copy, it covers most everything you need. It was awaiting review at HP Tuners but I don't know that...
  5. Yes, if the MAF tube is smaller you may need to...

    Yes, if the MAF tube is smaller you may need to raise the MAX and Vice Versa. Turn LTFT on and use the fuel trims to dial in the MAF, if you know the size difference you can work out the percentage...
  6. You need to set the dynamic airflow to 500 rpm...

    You need to set the dynamic airflow to 500 rpm and dial in the MAF without the VVE impacting it, once the VVE and MAF return the same mixture and fuel trim set the predicted coefficients to 0 and...
  7. Yep, its not new.

    Yep, its not new.
  8. I used to tune PD Superchargers 4-5 per weeks for...

    I used to tune PD Superchargers 4-5 per weeks for about 3 years, I had this problem on a number of occasions and had to do the 2 Bar OS upgrade (all Australian OS have this) I had to re-tune maybe...
  9. Oh, I just saw there is no OS upgrade option,...

    Oh, I just saw there is no OS upgrade option, that sucks. Log the VE airflow channels, if they drop to 0 its an ecu error.
  10. There is a command and an Intake Valve temp...

    There is a command and an Intake Valve temp correction, Set the open loop table to your desired mixture when cold and then adjust the ITV gain to achieve that mixture.

    117472
  11. This is glitch I have seen on many occasions and...

    This is glitch I have seen on many occasions and have logged multiple tickets with HP over, you cannot run the VVE without the MAF, you need to use the speed density OS upgrade. One issue is the ecu...
  12. If you have NN off tune the VE, but you will...

    If you have NN off tune the VE, but you will never get it 100% while the car has variable cam.
  13. Replies
    3
    Views
    322

    Are you sure this has a MAP sensor? Nissan went...

    Are you sure this has a MAP sensor? Nissan went away from having a MAP sensor in Y62 Patrol, its MAF, they use tables to estimate MAP based on injector Pulse and intake manifold pressure. This...
  14. Replies
    3
    Views
    322

    Can you put the stock tune file up?

    Can you put the stock tune file up?
  15. Thread: E92 tune

    by 4wheelinls1
    Replies
    2
    Views
    485

    Post the tune.

    Post the tune.
  16. Replies
    8
    Views
    386

    I have seen before where the fuel system is set...

    I have seen before where the fuel system is set up wrong with the non-return valve after the regulator so the pressure would spike on hot shut down due to heat soak, if you have an aftermarket fuel...
  17. Replies
    16
    Views
    1,250

    Lets cross that bridge if we come to it, you are...

    Lets cross that bridge if we come to it, you are not out of injector duty, your stock injectors are more than big enough, if fuel pressure is not the issue I'll put my thinking cap back on.

    As...
  18. Replies
    16
    Views
    1,250

    You have not driven the vehicle the same in both...

    You have not driven the vehicle the same in both logs so its not possible to compare apples, however the fuel trim is better with the stock MAF curve. The modified curve is larger and should be very...
  19. Replies
    8
    Views
    386

    Raise the desired IAC area MAX, this limits the...

    Raise the desired IAC area MAX, this limits the opening at idle. Should be 200.
  20. Replies
    16
    Views
    1,250

    Does your car have an FSCM and a pressure sensor?...

    Does your car have an FSCM and a pressure sensor? If not it will constantly display the desired pressure. Your read does not include one in which case you need to test it with a mechanical gauge.
  21. MBT is used for torque calculation, if the MBT is...

    MBT is used for torque calculation, if the MBT is raised and the actual timing is much lower than MBT it will calculate less torque, the trans uses the torque value for line pressure.

    There are...
  22. Replies
    20
    Views
    1,494

    The cost is much lower, you need tokens which are...

    The cost is much lower, you need tokens which are only $2USD, 25 for one vehicle for 1 month use of the HP processor.

    Having done all three methods I can say very honestly this is the best by far...
  23. Replies
    20
    Views
    1,494

    I have done about 40 5.7 Ram vehicles with...

    I have done about 40 5.7 Ram vehicles with superchargers with NN retaining, fortunately there are only 2 significant OS variation so once they have been done the same NN values can be used for the...
  24. The normalised torque sets the scale of what...

    The normalised torque sets the scale of what represents 100% load. The torque is calculated based on the torque to load conversion. If the normaliser is 1000Nm and the vehicle load is 100% then the...
  25. Download the BlueCat Transmission shift tool,...

    Download the BlueCat Transmission shift tool, that will get you in the ballpark quickly, its a great little program. ...
Results 1 to 25 of 276
Page 1 of 12 1 2 3 4