Search:

Type: Posts; User: showelljr

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    22
    Views
    3,206

    Crawled around it a good bit when I was...

    Crawled around it a good bit when I was installing the WB sensor and grabbed things to see if they were loose, tapped on things to see if anything sounded loose or such and didn't find anything out...
  2. Replies
    22
    Views
    3,206

    Ok, here is a log and the latest tune from a...

    Ok, here is a log and the latest tune from a little fueling added on the in gear portion. I add EQ Commanded and Transmission status. I tried adding AC clutch but it was not working and it may...
  3. Replies
    22
    Views
    3,206

    Alright so got the wideband in and finally...

    Alright so got the wideband in and finally figured out that one of my mpvi2 interfaces is a pro and one is not so I had to swap to get the WB to log in the scanner. Now, when I go to adjust the tune...
  4. Replies
    22
    Views
    3,206

    I do have a wide band setup. I guess I can just...

    I do have a wide band setup. I guess I can just pull one of the narrowbands and put the wideband in it for now? I would have to make up a harness and maybe plug it into the power outlet and wire it...
  5. Replies
    22
    Views
    3,206

    Here is the first file I saved out of the truck...

    Here is the first file I saved out of the truck before I started doing anything.
  6. Replies
    22
    Views
    3,206

    These were the last two things I saved before...

    These were the last two things I saved before coming in from the garage.
  7. Replies
    22
    Views
    3,206

    Got to be something I am over looking for the...

    Got to be something I am over looking for the Idle setup once in gear or AC comes on to add more air from the IAC, its bound to still be operating on 5.3 airflow needs and not the extra 6.0...
  8. Replies
    22
    Views
    3,206

    So, I still need to adjust the physical sensor on...

    So, I still need to adjust the physical sensor on the TB? Ok, just looked at it a little closer and see the screw coming up from the bottom on the flange of the cable guide for the blade.
    ...
  9. Replies
    22
    Views
    3,206

    Ok, out here on the truck now, after getting my...

    Ok, out here on the truck now, after getting my wifi fixed for laptop.

    Engine > Fuel > Oxygen Sensors > LTFT is now disabled.

    MAF is failed Engine Diag > Airflow > MAF Freq Fail High at 0hz
    ...
  10. Replies
    22
    Views
    3,206

    Okay here is some more adjustments. It does good...

    Okay here is some more adjustments. It does good on a cold start and hot start up. Idles fine. Put the truck in reverse and its noticeable it went into gear but not violent. Back to neutral is...
  11. Replies
    22
    Views
    3,206

    working 3am-3pm sucks so sorry for the delay. ...

    working 3am-3pm sucks so sorry for the delay.
    I did a write entire with your file and add the stft and ltft for both banks in the scanner config. This file has a start or two and a few low rpm...
  12. Replies
    22
    Views
    3,206

    So I compared this file to mine and made the...

    So I compared this file to mine and made the adjustments that showed up. Truck doesn't want to start cold but once it starts getting some heat in it, it still stumbles but does better. I have...
  13. Replies
    22
    Views
    3,206

    Well just talked to the guy that swapped wanting...

    Well just talked to the guy that swapped wanting to know what I was running into and come to find out he swapped a 6.0 into the 5.3 with this cam. Told him it would explain the huge discrepancy in...
  14. Replies
    22
    Views
    3,206

    2000 5.3 Truck Norris Cam

    I am helping a friend with a truck that had a cam swap in it, BTRtruck norris int 212 exh 22x lsa 107.5 int lift .553 exh lift .553. So its a P01 setup and I am trying to figure it out, obviously...
  15. I am using the same switch to monitor...

    I am using the same switch to monitor transmission pressure and am going to plug the .009 and zero into the user defined pid for the prolinkj #2 input and I will let you know what I get. Its logging...
  16. My box showing up under another serial numbered box

    I have a guy that we did the motor in and tuned it. I saved the file and all was well. He gets another guy to do some WOT tuning and I send him the file I read and he sends a file back. Now the...
  17. Replies
    0
    Views
    785

    Fuel Temp Monitoring

    Is anyone logging fuel temp of their setup? Running twin 450's and its a return system. I have a 1/8npt connection that I was logging fuel pressure just to make sure that the regulator was holding...
  18. Replies
    14
    Views
    3,993

    CL is lean

    Okay had some wiring issues with the trans and got that all fixed.....set my scanner up to log ltft+stft against airflow HZ and kept watching it......right now just working on idle.......in the range...
  19. So, do the math from the error and apply to to...

    So, do the math from the error and apply to to the MAF table of frequency vs air flow?
  20. Replies
    14
    Views
    3,993

    okay here is a logfile......92292

    okay here is a logfile......92292
  21. Replies
    14
    Views
    3,993

    Alright, little update......truck is running but...

    Alright, little update......truck is running but not driving yet. The startup is okay and as it warms up, its fine in OL, once it gets into CL the AFR, wideband installed 24" from turbo exit, it...
  22. Replies
    14
    Views
    3,993

    Okay I found it..... It was not right, but I...

    Okay I found it..... It was not right, but I found it under Engine Diag > Airflow and made the adjustments.

    Thanks, will keep up to date and reach out for some help shortly....
  23. Replies
    14
    Views
    3,993

    Okay, so got some updates, I was able to apply a...

    Okay, so got some updates, I was able to apply a 2bar patch after reading what was in the ECM, applied, saved as a new file, opened the new file, double/half setup stoich for the injectors, and then...
  24. Replies
    14
    Views
    3,993

    91372 the decimal left right button moves what...

    91372

    the decimal left right button moves what is in the data, I can't get the ms across the top to change to 0 .125 .250 .375 .500 like the spreadsheet is from ID...?.I can change the units but...
  25. Replies
    14
    Views
    3,993

    So in the Excel sheet from ID for the short pulse...

    So in the Excel sheet from ID for the short pulse adder, the items are not lining up so do I go through and grab the data that matches the headers and the interpolate horizontally through the ones...
Results 1 to 25 of 30
Page 1 of 2 1 2