Search:

Looks like there is some information available on the Bosch ECU but no seeing anything on the immobilizer side of things.

The Tuning School has some MPV2+ with Pro Features and 4 credits in stock.

https://thetuningschool.com/collections/hp-tuners/products/hp-tuners-mpvi2-1

Makes his first and only post and it is negative who knows if he even has an issue !! So frustrating

Try being on their side.

Lets say you know a PID that is unknown to HP tuners. This would allow you to add it too your configuration.

To me this should be included with the pro feature set. If I have a non standard (to HP...

The resistor will make you CAN bus "more" correct but I feel this statement of yours carries a lot of value. In my quest to learn CAN I have found some ECU's don't speak unless spoken too. If the...

For termination you just need a 120 ohm resistor across the bus on the farthest end. The if you check across the bus you will show 60 ohms.

The ECU is terminated and your harness isn't and nothing on the bus is either and this is common. The ECU is on one end 120 ohms and and you should have another terminator on the far end but really...

There are cheap tools available but sometimes the software then kind of sucks. Maybe try asking for help logging CAN on FB, maybe able to find someone local. They don't need to be car guys just...

It should have another terminator on the bus but that is some of the beauty of CAN, even a poorly configured bus will often work.

I am odd and it would be honestly fun to me to log the can with...

Starting simple key on engine off check resistance across the CAN bus 60 ohms is best 120 is possible.

I assume all you have on the CAN is the PCM and Dakota Digital system.

I have to admit...

1) Can I use already bought obdlink mx+ to connect VCM with vehicle?
No

2) If not, what can I hardware do I need?
Very difficult question, there are many different tuning options and...

I can see this is going well

tunerstudio does seem ideal for a megasquirt based ECU project.

You cant blame HP tuners for the learning curve, their software makes things really simple compared to open source, you will just have to learn a little.

For you issue you can bring it up here but...

dr.mike is working on an adapter that takes the AEMnet CAN and will put that data onto the pre-CAN data streams. The J1850-VPW is currently under test.

That thread is located here...

As mentioned above by dr.mike the 30-0310 re-flashed to function like the 30-0334 works perfectly in stand alone.

As for stand alone prolink this email was as of 04/13/2022 (however they did...

Goat Rope garage has some pretty good YouTube videos on setting up your histograms for this.

When you set up scanner you have to make sure your scaling on both axis between scanner and editor are...

Received the test device fondly called "brick" today.

Short on time and quickly fitted the housing with Dremel (functionally installed).

Will try and can some initial testing tomorrow as timing...

From the 30-0310 instructions

Bus Termination
All AEMnet/CAN networks must be terminated to have an equivalent of approximately 60 Ohms of resistance. Generally, this means a 120 Ohm resistor...

Put a 60 ohm resistor across the the CAN wires. Neither the Prolink+ or the 30-0310 have any CAN bus termination. Anything from 60 to 120 should work fine.

As of Friday the Prolink+ CAN still only...

I have a 30-0310 running with dr.mike firmware and it works great for my application. I great tool!!

At least with the MPVI2+ and the Prolink+ they currently have the two Analog channels working in Standalone with firmware 5.1.17

The CAN channel is still vanishing in stand alone

so Half Fixed!!

At least with the MPVI2+ and the Prolink+ they currently have the two Analog channels working in Standalone with firmware 5.1.17

The CAN channel is still vanishing in stand alone

so Half Fixed!!

At least with the MPVI2+ and the Prolink+ they currently have the two Analog channels working in Standalone with firmware 5.1.17

The CAN channel is still vanishing in stand alone

so Half Fixed!!

I was just interested if the AEMnet CAN of the device was terminated since the wide band and the device are forming their own bus.

All Good