Search:

Type: Posts; User: Exley

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    248

    From what I could tell this is the pedal...

    From what I could tell this is the pedal threshold to trigger the WOT Lambda fuel table. I lowered mine to 75% and it really helped with pedal feel. If you leave it stock, you start to hit the max...
  2. Replies
    5
    Views
    845

    Excited for this too! Have a Mk7 GTI

    Excited for this too! Have a Mk7 GTI
  3. Replies
    3
    Views
    772

    Mine will do it warm or cold. It seems to be when...

    Mine will do it warm or cold. It seems to be when there is higher humidity. I can't tell you for sure if it did it stock. If it is something in the tune it would be a side effect, I haven't touched...
  4. Replies
    3
    Views
    772

    http://www.focusst.org/forum/focus-st-performance/...

    http://www.focusst.org/forum/focus-st-performance/41258-low-speed-low-load-sputter-misfire-4.html

    Does that sound similar to what you are experiencing? There's no real answer in the thread, but I...
  5. Replies
    0
    Views
    483

    2007 Mustang GT Catalyst Readiness Test

    I was curious if parameters that controlled when the catalyst monitor runs could be added to my OS similar to this thread describing the O2 monitor on the coyotes
    ...
  6. Replies
    16
    Views
    2,185

    What about taking airflow out of these tables in...

    What about taking airflow out of these tables in the 2200 row?

    68771
  7. Replies
    16
    Views
    2,185

    Oh it's loud. And i still have the stock H-pipe

    Oh it's loud. And i still have the stock H-pipe
  8. Replies
    16
    Views
    2,185

    If you haven't already try messing with the...

    If you haven't already try messing with the "Mult" tables under Idle -> Airflow this adds airflow to the base idle airflow based on engine run time and engine coolant temp. Pretty sure the 0 second...
  9. Replies
    7
    Views
    1,194

    Maybe Eric can confirm. I think this is the...

    Maybe Eric can confirm. I think this is the master switch for the wheel torque error check and the associated wrench light when there are too many wheel torque errors
  10. Replies
    7
    Views
    1,194

    I felt a pretty big difference maxing out "Tip-In...

    I felt a pretty big difference maxing out "Tip-In Torque Rate Max" under Torque Management. This table has to do with how fast the throttle is allowed to react to the requested torque, if I...
  11. Replies
    10
    Views
    2,233

    Thank you! Planning on dialing in my transients...

    Thank you! Planning on dialing in my transients when it gets warmer out!
  12. Replies
    5
    Views
    1,390

    Interesting. I thought those would return Flow...

    Interesting. I thought those would return Flow and Pressure. That is how mine is laid out in the editor.

    Do they mirror each other? ex. if i made a histogram with 1 ,2, 3 ect as the x and y axis...
  13. Replies
    6
    Views
    1,781

    For anyone following this ...

    For anyone following this

    http://www.hptuners.com/forum/showthread.php?62028-Launch-Assitance-Gear-Shift-Hang-for-Manual-Trans
  14. Replies
    6
    Views
    1,781

    Thanks for the confirmation. Just sent an...

    Thanks for the confirmation.

    Just sent an email to support.

    Also wanted to thank you. I've been reading your posts here and on other forums about LSPI and the general logic of the ecoboost...
  15. Replies
    6
    Views
    1,781

    I tried this over the weekend. Changed Load...

    I tried this over the weekend. Changed Load Switch to 1, didn't notice any difference in the clutch out assist or the rev hang anticipating the next gear.
  16. Replies
    6
    Views
    1,781

    Eric, Would the Load Switch setting under...

    Eric, Would the Load Switch setting under transmission have anything to do with this? I can send in the files if that would help.
  17. Replies
    6
    Views
    1,781

    Shift and launch assist 2013 Focus ST

    Hi I flashed my 2013 Focus ST with a canned tune and read the car to see what they changed. The handheld had the option to disable "shift assist" and "launch assist." Comparing my stock file to what...
  18. Replies
    8
    Views
    1,697

    What pulley on the whipple?

    What pulley on the whipple?
  19. Replies
    70
    Views
    19,850

    Does anyone have any more info on "clip torque"...

    Does anyone have any more info on "clip torque" under ETC torque management? The stock value for TCS is 7.38. The value is in ft/lbs not a ratio
  20. Replies
    162
    Views
    50,793

    Sweet!!!! :yay:

    Sweet!!!! :yay:
  21. I would email support and see if the Acceleration...

    I would email support and see if the Acceleration and Deceleration transient tables can be added to your operating system. I was having trouble with a lean tip in. Adjusting the manifold volume...
  22. Replies
    9
    Views
    3,322

    Just wanted to chime in. My 07 Mustang would not...

    Just wanted to chime in. My 07 Mustang would not run the catalyst or EVAP tests after installing my Whipple. o2 and o2 heater did run after two short drives. AFAIK I did not change any hidden...
  23. I would take another look at your Driver Demand...

    I would take another look at your Driver Demand table. I've never seen one maxed out like that before. Has that worked for you before?
  24. Replies
    8
    Views
    3,130

    You could try doing what ElecTech says about...

    You could try doing what ElecTech says about deleting the file in this thread.

    http://www.hptuners.com/forum/showthread.php?51718-VCM-Scanner-2-25-Ford-Tips/page4

    I have a feeling the knock DMR...
  25. Replies
    8
    Views
    3,130

    It wasn't in 2.24 last time I used it on my 2007....

    It wasn't in 2.24 last time I used it on my 2007. I believe DMR scanning is in the process of being added to the 2.25 beta scanner
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4